RadioMaster Zorro Radio – ELRS version
2 in stock
RadioMaster Zorro Radio – The Compact Class-Leader.
Featuring an ergonomic design, large bright LCD screen in the perfect viewing position, travel adjustable HALL sensor gimbals, a nano size external RF module bay, built-in USB-C Charging, USB-C Data port for updating and playing simulators, rear and top assignable push buttons, scroll wheels, RadioMaster’s 7 button menu navigation system, headphone audio output, external power source input and a host of RF options the RadioMaster Zorro is set to change the game once again. The external module can support TBS Crossfire.
*This is the ELRS version
Supports OPENTX & EDGETX
Adjustable Hall Gimbals
External Module Bay
Direct Battery Charging
Supports External 2S Battery Power Supply
Foldable Antenna
Ergonomically Designed
$110.99
2 in stock
Specifications:
-
-
- Physical Dimensions: 170*159*108mm
- Weight: 350 grams
- Operating Frequency: 2.400GHz-2.480GHz
- Internal RF: ELRS, Module back option for Crossfire or others
- RF Power: Up to 250mw ( CE & FCC Versions will be available)
- Antenna Gain: Folding 2db
- Operational Current: 160mA@8.4V
- Operational Voltage: 6.6-8.4v DC Supports external 2S Power Supply
- Control Distance: > 2km @ 20dbm
- Receiver and Power Output dependant > 2km @ 20dbm
- Operating system: OpenTX / EdgeTX Compatible
- Control channels: Maximum 16 (Rx dependent)
- Display: 128*64 Monochrome LCD
- Battery: 2 x 18350 (Not included)
- Charging:Built in USB-C Charging
- Gimbal: Hall-effect
- Module Bay: Nano Size (Compatible with TBS Nano Crossfire / Nano Tracer / IRC Ghost)
- Firmware Upgrade Method Via USB or SD card
- Supports OPENTX & EDGETX
Included:
- 1x RadioMaster Zorro Radio Controller – ELRS
-
Based on 0 reviews
Only logged in customers who have purchased this product may leave a review.
Related products
-
Radio Accessories, Radio Transmitters, TBS
TBS Tango 2 Module Bay Add-On
This is an after-market mod to add a module bay to your Tango 2. The module bay sticks to the back of your Tango 2 and plugs into the receptacle board of your Tango 2.
Installation process
- Install the FPC cable to the PCB.
With the blue side facing up, lift the lock and slide the cable in then lock it down. - Feed the cable through the bottom and place the PCB to the module bay.
- Turn the module bay around to make sure everything fits accordingly.
- Close the case with the 2 screws provided
- Use a dremel, knife or solder tip to cut a small hole accoridng to the outline.
- Slide the flex PCB through the drilled case.
- Clean the back surface and tape the Tango 2 module bay down
- Â Install the FPC cable into the receptacle.
- Close the Tango2 case, and you’re done!
*IMPORTANT NOTE
*The first batch of Tango 2 shipped WITHOUT module bay capability. Please verify that there is a connector (in pictures above) before purchasing this add-on. Upgrade PCB’s can also be purchased!
Also, whenever opening up your Tango 2 in future, you will need to open the module bay and release the flex PCB from the socket.*We have discovered that XJT mini modules are using a pin that we did not anticipate for use in our module bay. It appears that the XJT mini module is the only module on the market that uses this pin.
Due to a hardware incompatibility between the XJT mini module and the Tango 2 (V2 and up) boards, the Tango 2 will NOT be able to support the XJT mini module.
SKU: TBS.T2ModB - Install the FPC cable to the PCB.
-
-
Radio Transmitters, TBS
TBS Tango 2 FPV Radio Controller Transmitter
The Tango 2 is released as the smaller radio available, yet it comes with full sized Hall gimbals, Freedom TX (temporary OpenTX fork), and the lowest latency of any TX system.
Team BlackSheep has been at the forefront of perfecting the interface between FPV drone and mind. The TBS Tango 2 changes how radio remote controls will be from here on out! Despite being the smallest remote control available, it comes with full size HAll gimbals, full-featured FreedomTX (temporary OpenTX fork), the lowest end-to-end latency of any remote and transmission system, unbreakable 3 & 2-position switches, open source operating system, built-in battery, USB-C charging, and so much more! It’s not just a retouched game controller, it was designed from the ground up for R/C! The form factor and features make it the ideal take-anywhere, fly-anytime remote control.
CROSSFIRE Built in
The first radio with TBS Crossfire built in. This significantly lowers your cost, increases reliability and minimizes set up time. And the cherry on top are the LUA scripts being part of the familiar user interface. The antenna swivels out of the way, or doubles as a kick-stand when resting. TBS Cloud ready to go from the start. It all just makes sense.SKU: TBS.TANGO2. -
Category Name, Radio Accessories, Radio Transmitters, RadioMaster
RadioMaster 4IN1 2.4GHz Micro Nano/JR Transmitter Module
Category Name, Radio Accessories, Radio Transmitters, RadioMasterRadioMaster 4IN1 2.4GHz Micro Nano/JR Transmitter Module
The RadioMaster 4IN1 External Nano/JR Module, which is a multi-protocol module that integrates CC2500, NRF24L01, A7105 and CYRF6936 RF chips. This is external nano module can also be used on JR modules, with the included JR adapter.
RM 4IN1 is compatible with more than 70 RF protocols, including DSMX, Flysky, SFHSS, HiTec, HoTT, OMP, Radiolink, Frsky and many more.  The module features a +20dBm RF gain, a 2.4GHz frequency band, and an operational voltage of 4.5-8.4V.
Designed for OpenTX and EdgeTX systems, the RM 4IN1 module allows the radio to connect with most mainstream protocols on the market. Though when this module is used in conjunction with a suitable EdgeTX or OpenTX compatible radios such as the TX16s, TX12 or Zorro, the RM 4in1 module can be used as a wireless trainer link to a student radio such as another TX16s, TX12, Zorro or any other radio capable of transmitting DSMX, Frsky or Flysky protocols.
SKU: RM.4IN1.MODULE.
There are no reviews yet.