Product Carousel Tabs
TBS Tango 2 Module Bay Add-On
This is an after-market mod to add a module bay to your Tango 2. The module bay sticks to the back of your Tango 2 and plugs into the receptacle board of your Tango 2.
Installation process
With the blue side facing up, lift the lock and slide the cable in then lock it down.
*IMPORTANT NOTE
*The first batch of Tango 2 shipped WITHOUT module bay capability. Please verify that there is a connector (in pictures above) before purchasing this add-on. Upgrade PCB’s can also be purchased!
Also, whenever opening up your Tango 2 in future, you will need to open the module bay and release the flex PCB from the socket.
*We have discovered that XJT mini modules are using a pin that we did not anticipate for use in our module bay. It appears that the XJT mini module is the only module on the market that uses this pin.
Due to a hardware incompatibility between the XJT mini module and the Tango 2 (V2 and up) boards, the Tango 2 will NOT be able to support the XJT mini module.
Happymodel PH2.0 1S USB Battery Charger
The Happymodel USB Charger is tailored for a 200-400 mAh battery. It has an LED light to indicate it is charging and the light will go off when it is complete. It features a 4.2V/4.35V switchable button as well.
Happymodel Crux 35 HDZero 3.5″ Quad – ELRS version
CRUX35 HDZero is an ultra-lightweight 3.5Inch FPV Freestyle FPV Racing Drone, the weight of the whole drone is only 108g for the digital HD version. The Crux35 uses Happymodel EX1404 high-efficiency motor and HQPROP 3.5-inch three-blade propeller to ensure the largest thrust-to-weight ratio under the most efficient premise, which can bring you a smooth Freestyle flying experience.
This HDZero version is equipped with Runcam Nano Camera and the HDZero Whoop VTX.
This receiver version is the SPI ExpressLRS.
ExpressLRS is the most popular RC link system.
NOTICE: ELRS SPI Version is updated to ExpressLRS v2.0 version
HDZero Nano V2 Camera
Runcam Nano V2 HDZero camera is a 4:3 and 16:9 selectable high definition 720p60 camera designed for HDZero VTX. It supports the camera menu for brightness, contrast, saturation, HV flip and other camera settings. It has excellent low light performance for its ultra-high sensitive sensor.
RadioMaster TX16S Foam Box Zipper Cover
Keep your TX16S safe in style with the official RadioMaster zipper carry case cover. This zipper cover is designed to work with the foam packaging you received your TX16S to offer a smart look and continent carry handle that will protect and prolong the life of the foam storage box.
Torvol LiPo Safe Bag – Stealth Edition
Stay safe, organized, and stealth! Now Torvol’s safe bag comes in all black.
Torvol LiPo Safe Bag is made of high quality, fire retardant fabric and a treated polyester shell, giving you the security and ease of mind to take your LiPo batteries with you wherever you want to race. It safely stores up to 15 LiPo’s.
The bag is purposefully designed to perfectly fit inside the Quad PITSTOP Backpack and Quad PITSTOP Backpack PRO, making it the perfect race companion.
Torvol Quad Pitstop Backpack Pro
“A quad backpack” is an understatement! Torvol’s FPV Bestseller: the most trusted racing backpack for professional drone pilots.
* The Torvol Quad PITSTOP Backpack PRO easily carries 4 race quadcopters and all equipment specific to your drone flight; goggles, transmitter, LiPo’s, tools and more.
* It features Torvol’s PITSTOP area. The Torvol smart zipper transforms the backpack into a portable workspace to adjust and modify your drone racing material quickly and effortless.
* This quadcopter backpack includes multiple organizer pockets and dividers which makes it highly customizable. There is ample space for your FPV gears and personal belongings. Larger items like a tripod and a foldable chair can be strapped to the outside.
*The dedicated laptop pocket on the back holds and protects a 15-inch laptop and a charger. An expandable rain cover integrated at the bottom, thick back padding and a hip and sternum strap ensure comfort and convenience while traveling to your race. Torvol’s CLEANSEAT keeps your pants neat on any outdoor space.
*One more extra, you can register on Torvol’s website under “Custom Nametag” to have your own engraved pilot name on it for free!
*LiPo safe pouch not included
Which quads and drones fit inside?
FPV Quadcopters of 6″ and less.
Cinewhoops and Racewhoops of 4″ and less.
DJI drones:
DJI Air 2S, FPV (without propellers), DJI Mini 2/SE, Mavic 2 Pro/Zoom, Mavic 3, Mavic Air, Mavic Air 2, Mavic Mini, Mavic Pro/Pro Platinium, Spark, Tello & Tello Edu.
NO Phantoms.
Autel drones:
Evo Lite, Evo Lite+, Evo Nano, Evo Nano+, Evo I, Evo II, Evo II Pro.
Parrot drones:
Anafi, Anafi Work/Extended/Thermal/FPV/Ai/USA.
Hubsan drones:
Ace Pro/Pro SE, Zino 2 Mini/Mini Pro, H501M, H501A, H501S, H501C, H216A, H502S, H507A, H507D, H502T, H502E, H107D, H111D, H109, H109S, H107C, H111C Nano, H122D, H123D.
NO Zino, Zino 2.
Yuneec drones:
Typhoon H, Mantis Q, Typhoon H3
Besides these brands, most drones on the market fit inside the Pitstop Pro.
Torvol Quad Pitstop Backpack Pro – Stealth Edition
“A quad backpack” is an understatement! Torvol’s FPV Bestseller: the most trusted racing backpack for professional drone pilots now in Stealth Edition!
* The Torvol Quad PITSTOP Backpack PRO easily carries 4 race quadcopters and all equipment specific to your drone flight; goggles, transmitter, LiPo’s, tools and more.
* It features Torvol’s PITSTOP area. The Torvol smart zipper transforms the backpack into a portable workspace to adjust and modify your drone racing material quickly and effortless.
* This quadcopter backpack includes multiple organizer pockets and dividers which makes it highly customizable. There is ample space for your FPV gears and personal belongings. Larger items like a tripod and a foldable chair can be strapped to the outside.
*The dedicated laptop pocket on the back holds and protects a 15-inch laptop and a charger. An expandable rain cover integrated at the bottom, thick back padding and a hip and sternum strap ensure comfort and convenience while traveling to your race. Torvol’s CLEANSEAT keeps your pants neat on any outdoor space.
*One more extra, you can register on Torvol’s website under “Custom Nametag” to have your own engraved pilot name on it for free!
*LiPo safe pouch not included
Which quads and drones fit inside?
FPV Quadcopters of 6″ and less.
Cinewhoops and Racewhoops of 4″ and less.
DJI drones:
DJI Air 2S, FPV (without propellers), DJI Mini 2/SE, Mavic 2 Pro/Zoom, Mavic 3, Mavic Air, Mavic Air 2, Mavic Mini, Mavic Pro/Pro Platinium, Spark, Tello & Tello Edu.
NO Phantoms.
Autel drones:
Evo Lite, Evo Lite+, Evo Nano, Evo Nano+, Evo I, Evo II, Evo II Pro.
Parrot drones:
Anafi, Anafi Work/Extended/Thermal/FPV/Ai/USA.
Hubsan drones:
Ace Pro/Pro SE, Zino 2 Mini/Mini Pro, H501M, H501A, H501S, H501C, H216A, H502S, H507A, H507D, H502T, H502E, H107D, H111D, H109, H109S, H107C, H111C Nano, H122D, H123D.
NO Zino, Zino 2.
Yuneec drones:
Typhoon H, Mantis Q, Typhoon H3
Besides these brands, most drones on the market fit inside the Pitstop Pro.
Happymodel SuperbeeF4 Lite AIO 1S FC 2.4GHz ELRS
The direct replacement AIO board for the Mobula6 HDZero. The default OSD is set to “MSP” since this is considered spare part for the Mobula6 HDZero.
If using this board with an analog camera you will need to change some settings in BetaFlight. Instructions can be found at SuperbeeF4
* ELRS version
Happymodel Pancake 2-6S F4 AIO Flight Controller SPI ELRS RX + 5.8GHz OpenVTX
Happymodel Pancake 2-6S F4 AIO Flight Controller SPI ELRS RX + 5.8GHz OpenVTX
The Pancake AIO was designed with the help of the ExpressLRS team. It features an onboard 2.4GHz ELRS SPI receiver as well as a 5.8 GHz OpenVTX with up to 400mw of power. It can be mounted using the 30.5mm or 20mm spaced holes.
Walksnail Avatar Digital HD FPV Goggles v1
Avatar HD Micro Camera/VTX Kit features a micro-sized digital camera and VTX that works with HD Goggles such as the Avatar and Fat Shark HD Dominator.
Note: This is the Flywoo rebranded. It doesn’t include the original walksnail packaging or the original walksnail antenna. Equipped with Top Circular Polarized Flywoo double antennas.
Flywoo Firefly Nano Baby 20 2S Micro Quadcopter ELRS – Analog
Flywoo Firefly Nano Baby 20 2S Micro Quadcopter ELRS – Analog
The Flywoo Firefly Nano Baby 20 2S Micro Quadcopter BNF Analog comes with Flywoo’s Nano Camera V2 1S and is equipped with the most efficient micromotor and the top AIO flight controller on the market!
* This is the ELRS Version
* Action Camera not included
Happymodel CrossF4 F411 1-2S 5A AIO Whoop Flight Controller with UART ELRS v3.0 receiver – ELRS 2.4gHz
Happymodel CrossF4 F411 1-2S 5A AIO Whoop Flight Controller with UART ELRS v3.0 receiver – ELRS 2.4gHz
HappyModel keeps them coming! Now with yet another fantastic whoop AIO. The HappyModel CrossF4 1-2S AIO Whoop Flight Controller (F4 FC / 5A 4in1 ESC) – Featuring F411 Flight Controller, with a built in serial UART ELRS for V3.0.
NOTE: Onboard blackbox enable method:
-Type the following command to CLI:
-set blackbox_device = SPIFLASH
-set flash_spi_bus = 2
-resource FLASH_CS 1 a14
Pay attention: Bind procedure is the same like Happymodel EP1/EP2 receiver, as you need to upgrade your ExpressLRS TX module to V3.X version first.
Alternative-Binding-Method-for-UART-Based-ELRS-RX
Onboard blackbox enable method:
Type the following command to CLI:
set blackbox_device = SPIFLASH
set flash_spi_bus = 2
resource FLASH_CS 1 a14
save
Fractal Engineering Fractal 65 Lite Frame Kit 1.5mm
This is the Fractal 65 kit without the 65mm whoop frame to chop up for the prop guards. You can provide your own (NBD, BetaFPV, or Happymodel), purchase the 65 frame from us, or even run it without the prop guards!
As you may know, Yves in Taiwan has created this unique kit consisting of a carbon fiber centerpiece with four detached ducts and an ultralight camera mounting system. The overall design is modular, customizable, durable and light-weight!
ViFly Whoopstor V3 1S LiPo/LiHV 6 Channel Battery Charger/Discharger BT2.0 PH2.0
ViFly Whoopstor V3 1S LiPo/LiHV 6 Channel Battery Charger/Discharger BT2.0 PH2.0
The new v3 version is finally here! ViFly’s new 1S whoop battery charger supports both PH2.0 & BT2.0. VIFLY WhoopStor 3 is the first 1S LiPo charger with storage function. It includes both charging and discharging functions. Just select your target voltage, it will do it for you automatically. It now features a buzzer to beep when one charging circle finished, if you don’t like the beeping, you can turn the buzzer off manually.
DarwinFPV CineApe25 4S 2.5″ Cinewhoop Quad ELRS 2.4GHz – Choose VTX
DarwinFPV CineApe25 4S 2.5″ Cinewhoop Quad ELRS 2.4GHz – Choose VTX
CineApe25 is DarwinFPV’s first cinematic whoop FPV drone. The frame is composed of upper and lower carbon plates and a high-strength injection guard, which is very strong and crash-resistant, and easy to disassemble. The motor adopts a 1504-3600KV long-life motor; we abandoned the traditional AIO solution and adopted the split design of the F4, 30A stack to reduce the maintenance cost in the future. The accessories adopt mature and stable solutions to maximize the durability and reliability of the drone.
CineApe25 is a very cost-effective whoop FPV drone. It not only solves the worries of beginners about the high-risk factors and high threshold of assembly but also improves the after-sales experience. If you are still struggling with which FPV drone to buy, DarwinFPV CineApe25 may be your best choice!
Features:
Comes with high-strength one-piece injection-molded propeller guard, which has higher safety, stronger and more durable frame, also reduce the probability of risk, so you have more confidence to fly.
The new ducted aerodynamic design greatly optimizes power efficiency, and with the 1504-3600KV long-endurance motor, the CineApe 25 has a battery life of up to 9mins.
Compared with traditional stacks, we have treated the CineApe 25 stack with glue to protect it, which greatly reduces the risk of damage to the stack due to contact with metal particles, fine sand and gravel, weeds or dewdrops, etc.
The external Type-C parameter adjustment port is convenient for parameter adjustment.
It comes with quick-release design only needs to remove 7 screws to separate the top plate and the injection molding guard, which can easily deal with the scene in which accessories need to be replaced urgently.
The stack has built-in SD card slot and reserves rich interfaces resource, which is facilitate upgrade and DIY in the future.
Walksnail Avatar HD Goggles X (Open Box)
** IMPORTANT NOTE:
This item is new but sold as “opened box” at a lower price. Customer returned it day after purchase due to not fitting the contours of his face correctly, leading to some light leakage. All items are working and in mint condition.
The rumored Walksnail Avatar HD Goggles X!
These goggles are packed with the latest tech features, including HDMI and CVBS input, a wider pupil adjustment range, improved clarity and comfort, and for the first time, a removable HD receiver module. It’s been designed with research and development and market feedback, ensuring maximum comfort and versatility for users. Enjoy the peak performance with this advanced HD Goggle set.
BetaFPV 1S 450mAh 30C LiPo Battery BT2.0 (4 pack)
All batteries need to ship via a ground delivery service. Please select a Ground Advantage (USPS) or UPS ground!
After BT2.0 300mAh 1S battery, BT2.0 450mAh 1S battery is following close at its heels. As the first 450mAh 1S battery with BT2.0 connector in the current market, it has exclusive designed BT2.0 connector, which has broken through the bottle-neck of PH2.0 crappy crimped pins. What’s more, it is highly recommended for Emax Tinyhawk, which achieved dynamic balance, longer flight time and better performance, just need to simply modify its connector to BT2.0 connector.
BT2.0 Connector – the most significant revolution in 1S Whoop Drone.
Happymodel Mobeetle6 65mm – ELRS version
Happymodel’s new Mobeetle6 BNF is the lightest 65mm mass produced whoop in the world! The DiamondF4 Flight controller and 0702 motors were inspired from Angry Don FPV. A whoop style 65mm that includes a freestyle frame so you can fly as you prefer!
Happymodel Crux 35 HDZero 3.5″ Quad – ELRS version
CRUX35 HDZero is an ultra-lightweight 3.5Inch FPV Freestyle FPV Racing Drone, the weight of the whole drone is only 108g for the digital HD version. The Crux35 uses Happymodel EX1404 high-efficiency motor and HQPROP 3.5-inch three-blade propeller to ensure the largest thrust-to-weight ratio under the most efficient premise, which can bring you a smooth Freestyle flying experience.
This HDZero version is equipped with Runcam Nano Camera and the HDZero Whoop VTX.
This receiver version is the SPI ExpressLRS.
ExpressLRS is the most popular RC link system.
NOTICE: ELRS SPI Version is updated to ExpressLRS v2.0 version
Flywoo Firefly 1S Nano Baby Quad 40mm V1.2 (Deadcat style frame) ELRS
Flywoo Firefly 1S Nano Baby Quad 40mm V1.2 (Deadcat style frame) ELRS
Firefly 1S Nano Baby Quad is an 20g ultralight 1S Quad best for freestyle and crusing. Pilots can enjoy up to 8 minutes and 45 seconds flight time with Flywoo’s latest 1S 450mah battery ! Through a lot of tests, Flywoo has found the best configuration for Firefly 1S nano baby quad!Suitable for cruising super long flight time or ripping freestyle!
Last but not least, it is very quiet, like a mosquito, suitable for both indoors and outdoors.
** IMPORTANT NOTE:
Please do not try to update the ESC firmware as it may cause damage.
**Default ESC firmware: O_H_5_REV16_8-48K
Main Changes to V1.2 :
Modified the design of the bottom plate. The structure of the bottom plate is more reasonable and stronger . The battery can be placed either horizontally or vertically.
Upgraded to GNB27 V2 connectors for better current flow from battery . ( Note: GNB27 V2 is very tight, but it will become more suitable after a few uses.)
Flywoo Explorer 1S 450mAh 80C Battery 4.35v GNB27 V2 (4 pack)
Flywoo Explorer series batteries are specially designed for long flight time and all are high voltage battery. Using this battery will give you a significant increase in flight time as well as a bit more power over the stock battery.
Fat Shark Scout HD FPV Goggles
The Scout HD was Fat Shark’s first HD digital FPV goggle and the result was spectacular! Unparalleled image quality is achieved with a 1080p display viewed through Fat Shark’s patented folded optical engine. The 3.5” panel delivers a crisp 44-degree FOV image at 60 fps with compatibility with Shark Byte transmitters. Scout retains a reputation as a high-performance goggle at an affordable price while maintaining anti-fog fan features, comfortable form factor, and glasses accommodating faceplate.
Gemfan 1610-2 40mm (1.5mm Shaft) Propeller (4 pack)
A 40mm bi-blade prop from Gemfan. These are a fit on popular quads such as the Happymodel 1S Mobula 7/ Mobula 7 HD, Moblite7 HDZero 1s, and others with a 1.5mm center hole with prop length of 40mm.
Happymodel ES24TX Slim Pro ELRS TX Module
This Slim Pro TX module is designed by Happymodel and based on the open source- ExpressLRS which is a very popular low latency and high packet rate RF module for RC Airplane and FPV Racing drone. Its main hardware architecture is ESP32, ESP8285 and SX1280 RF chip. The ES24TX Slim Pro module is a complete solution which is already pre-loaded with the Expresslrs firmware and it’s plug and play for Frsky X-lite/X-lite pro/X9 Lite , TBS Tango2.
This Slim Pro module comes with an aluminum alloy shell and is equipped with a cooling fan that automatically works when the module is working at 250mw.
The slim pro TX module supports a maximum power output of about 1000mw, this would be very useful for Long Range FPV.
Happymodel Mobula7 1S 75mm Whoop – ELRS version
It’s always Whoop Season! This is one of your best options for a 75mm. You get unbelievable video range from the 400mw vtx. The new RS0802 motors come with a new unibell design using a 1.5mm shaft. Performs with nice precision.
ELRS version
Happymodel ELRS 2G4 Whoop Flight Controller
The world’s first AIO 5in1 F4 flight controller with integrated SPI 2.4GHz ExpressLRS receiver has been launched. The flight controller integrates SPI controlled 2.4GHz ExpressLRS receiver, Dshot protocol 4-in-1 ESC, 5.8GHz 40ch video transmitter and Betaflight OSD. Ultra-small size and ultra-stable remote control range can improve the range of the original SPI receiver. And because the 2.4GHz ExpressLRS receiver is equipped with the SX1280 radio frequency chip with high sensitivity, high packet rate and low latency, this flight controller is the one that all Race/Freestyle pilots needed. It is suitable for use in Tiny whoop Race or Toothpick Freestyle, and can also be used in 1S ultra-lightweight Nano Long Range platform.
HappyModel EP2 2.4GHz RX ELRS Receiver
Happymodel’s 2.4GHz ELRS nano series receiver with tiny ceramic antenna.
The PP RX was designed by @Jye Smith from the ExpressLRS development team. Its main hardware architecture is STM32L432KBU6 MCU and SX1280 RF chip. It has a built-in ceramic antenna, which is super light and small in size.
On the basis of that PP RX, Happymodel has developed the Nano 2.4GHz RX of ESP8285 version named EP1 and EP2. The RF module of EP1/EP2 is the same as PP RX and uses ESP8285 MCU. You can upgrade firmware via WiFi!
Due to the low-latency and high-refresh-rate RF module, they are very comfortable for FPV race and Long Range FPV. These are very suitable for Tiny Whoops because of the ultra-light and Nano size!
Note: This is the EP2 RX Version
Happymodel Mobula 7 1S 75mm HD recording Whoop – ELRS version
Happymodel continues to innovate with this 75mm whoop that can record in 1080 HD and features an on-board blackbox for gyroflow functionality.
Features X12 AIO board and a 400mw vtx. You’ve seen the reviews!
ELRS version
Happymodel X12 1-2S AIO Whoop F4 Flight Controller 12A ESC – ELRS version
Happymodel X12 1-2S AIO Whoop F4 Flight Controller 12A ESC – ELRS version
Happymodel X12 is a 5-in-1 AIO board featuring an F4 Flight Controller. It has an onboard 12A 4-in-1 ESC, 5.8GHz OpenVTX, with ELRS. This AIO has nice 400mw range great for any brushless whoop.
Happymodel EP82 VRX-Backpack Module
So what is this VRX backpack? This Happymodel “backpack”is designed to allow wireless communication between ExpressLRS, and other FPV-related devices for command and control, or for querying config. Currently there aren’t many VRX modules that can allow them to communicate with ELRS. This small ESP-based receiver can be “piggybacked” onto your VRX module, which allows ExpressLRS to control the band and channel that your goggles are set to. We call this device the “VRX-Backpack”.
Happymodel Crux3 1S Toothpick – ELRS Version
The Happymodel Crux3 ELRS 1S Toothpick is a great micro racing drone that features the Crazybee flight controller, EX1202.5 brushless motors, ELRS, and the Caddx Ant Camera to give you a great flying experience!
Note: Action Cameras are not included
Batteries not included
HDZero VRX Digital HD Receiver Module
The HDZero VRX is a digital HD 720p 60fps video receiver on 5.8GHz. It works with the HDZero/Shark Byte VTX module to transmit video. This time around HDZero releasing their very own HD receiver module, the VRX4! This module is compatible with any goggle that suports HDMI input.
HDZero Whoop VTX
The HDZero Whoop VTX is a digital HD 720p 60fps video transmitter capable of delivering up to 200mw on 5.8GHz. It works with the Shark Byte RX5.1 goggle module to transmit video, and with a remote controller to wirelessly control the parameters for the transmitter and camera.
HDZero Freestyle VTX
The HDZero Freestyle VTX is a digital HD 720p 60fps video transmitter capable of delivering up to 1000mw on 5.8GHz. It works with the HDZero/Shark Byte goggle module to transmit video, and with a remote controller to wirelessly control the parameters for the transmitter and camera. The HDZero Freestyle VTX is a digital HD 720p 60fps 5.8GHZ video transmitter.
The power input range is 2S –4S. Though the VTX integrates a surge protection circuit, a large capacitor (450+uF) parallel with battery leads is mandatory to smooth the power supply of the whole quad.
The VTX includes a BEC that converts 2S-6S to fixed 5.8V with maximum 5A output current. The VTX also includes an U.FL RHCP antenna.The HDZero Freestyle VTX is a digital HD 720p 60fps 5.8GHZ video transmitter.The power input range is 2S –4S. Though the VTX integrates a surge protection circuit, a large capacitor (450+uF) parallel with battery leads is mandatory to smooth the power supply of the whole quad. The VTX includes a BEC that converts 2S-6S to fixed 5.8V with maximum 5A output current. The VTX also includes an U.FL RHCP antenna.
RunCam HDZero Micro V2 Camera
Runcam Micro V2 HDZero camera is a 4:3 and 16:9 selectable high definition 720p60 camera designed for HDZero VTX. It supports the camera menu for brightness, contrast, saturation, HV flip and other camera settings. It has excellent low light performance for its ultra-high sensitive sensor.
HDZero Race V2 VTX
The HDZero Race VTX is a digital HD 720p 60fps video transmitter capable of delivering up to 200mw on 5.8GHz. It works with the Shark Byte RX5.1 goggle module to transmit video, and with a remote controller to wirelessly control the parameters for the transmitter and camera.
HDZero Whoop Lite Bundle
Been waiting for 1s micro and whoop sized quads to go digital? The wait is finally over! HDZero Whoop Lite is here to meet these needs: HDZero Nano Lite Camera is designed for feather-lite drones where every gram counts. At a weight as low as 1.5g, combined with the new Whoop Lite VTX at 4.5g with 0.4g dipole antenna enables a world’s-first production digital FPV solution of about 7g.
HDZero Nano V2 Camera
Runcam Nano V2 HDZero camera is a 4:3 and 16:9 selectable high definition 720p60 camera designed for HDZero VTX. It supports the camera menu for brightness, contrast, saturation, HV flip and other camera settings. It has excellent low light performance for its ultra-high sensitive sensor.
RadioMaster Zorro Radio – ELRS version
RadioMaster Zorro Radio – The Compact Class-Leader.
Featuring an ergonomic design, large bright LCD screen in the perfect viewing position, travel adjustable HALL sensor gimbals, a nano size external RF module bay, built-in USB-C Charging, USB-C Data port for updating and playing simulators, rear and top assignable push buttons, scroll wheels, RadioMaster’s 7 button menu navigation system, headphone audio output, external power source input and a host of RF options the RadioMaster Zorro is set to change the game once again. The external module can support TBS Crossfire.
*This is the ELRS version
Supports OPENTX & EDGETX
Adjustable Hall Gimbals
External Module Bay
Direct Battery Charging
Supports External 2S Battery Power Supply
Foldable Antenna
Ergonomically Designed
RadioMaster TX16S MKII EdgeTX RC Transmitter V4.0 Hall Gimbals – ELRS
RadioMaster TX16S MKII EdgeTX RC Transmitter V4.0 Hall Gimbals – ELRS
The best just got better! Introducing the TX16S Mark II, the ultimate open-source radio follow up to the original TX16S.
*This is the ELRS version
Support EdgeTX and OpenTX
V4.0 Hall Gimbals
Flat & Raised Grips Included
External Module Bay
Upgraded Design
RadioMaster Zorro Radio Carrying Case
This Carrying Case is designed to fit the RadioMaster Zorro Radio Controller. Keep your Zorro safe in style with this official RadioMaster carry case. This custom molded compact design case saves on space and looks great.
RadioMaster TX16S Foam Box Zipper Cover
Keep your TX16S safe in style with the official RadioMaster zipper carry case cover. This zipper cover is designed to work with the foam packaging you received your TX16S to offer a smart look and continent carry handle that will protect and prolong the life of the foam storage box.
RadioMaster Lubricant Set for Gimbals
RadioMaster’s lubricant and grease will have your gimbals feeling brand new. Your radio has been good to you, treat it right!
Use the damping oil for a silky smooth dampening effect on your throttle tension bar. Use the lubricating oil for gimbal bearings and moving parts.
ViFly Whoopstor V2 1S LiPo/LiHV 6 Channel Battery Charger/Discharger BT2.0 PH2.0
ViFly Whoopstor V2 1S LiPo/LiHV 6 Channel Battery Charger/Discharger BT2.0 PH2.0
ViFly’s new 1S micro/whoop battery charger is what you need if you are rippin 1S packs! Show your 1S the same love you show your larger batteries and keep them at storage levels to make them last.
The Whoopstor supports both PH2.0 and BT2.0. and features 6 Ports to Storage Charge/Discharge.
ViFly Beacon Wireless Self-Powered Drone Buzzer
VIFLY Beacon is an advanced self-powered drone buzzer for any types of quads. Based on the motion sensor, it can detect the abnormal movement of the quads and make the alarm automatically to help you find the lost quad easily when the quad crashed. Some aerial drones like DJI have GPS, but it only provides you the draft location when you crash it, with the sound help, you can find your quad precisely. Very easy to setup, everyone can make it work even you are a newbie. Install it on your DJI quads, FPV quads or airplanes to prevent the drone losing again.
Main Features:
Lost Drone Alarm by Motion Sensor
Some drones like DJI models are installed with GPS that only provide you the draft location, with the sound help, you can find your lost drone precisely. With the built-in motion sensor and lipo battery, VIFLY Beacon can detect the drone crash automatically and make the alarm to help you locate the lost drone.
Wireless, No Soldering Required
The mechanism of VIFLY Beacon is based on the motion sensor, attach it anywhere on the drone to detect the movement, no wire, no soldering.
Loud Sound & Bright LED
To easily find the lost drone in long distance, VIFLY Beacon is installed with a very loud beeper that the dB is over 100. In addition, the LED on VIFLY Beacon can flash automatically when the built-in light sensor detects the light darkness.
Anti Theft Technology
If someone wants to take the done away when it is in alarm status, VIFLY Beacon will beep continuously to warn the picker.
Position Light at Night
VIFLY Beacon LED light can flash automatically at night to make the drone visible when the built-in light sensor detects the darkness.
ViFly GPS-mate External GPS Power Module
Tired of draining your battery as you wait for the GPS fix? Wish the GPS was self-powered so that it didn’t have to get a new fix every time you plug up a new pack? Battery ejected during crash and now the GPS is useless? The GPS-mate is what you’re looking for!
Why Vifly designed the GPS-mate?
Most drone pilots have a problem when using the GPS on their drones. GPS modules are slow, and get interference. To get a fix, a pilot must wait many minutes for a GPS fix. To do this, everything must be powered, which drains the battery and causes extra interference. It also has potential risk to cause overheating issues to your quad components. In addition, when you finish a flight cycle and change the quad battery, the GPS needs to get a hot-start fix as the quad battery disconnected. We want to fix the pain, so we design and produce GPS-mate, the external power module just for GPS.
What exactly does the GPS-mate do?
VIFLY GPS-mate is an external power module just for GPS, there is a switch to turn on and off the unit. With this device, once the pilot wants to fly, he flips the switch and only the GPS gets powered. When the GPS fix finished, the pilot connects the drone LiPo. The drone LiPo powers the drone, and recharges the GPS battery. The GPS never loses power until the switch is turned off, so the pilot never needs to get another fix for the whole session.
We also embed VIFLY Finder 2 function into this device, it can work as a standard buzzer that controlled via your radio when the quad battery is connected, it also can work as a standalone buzzer that help you find the lost drone when the main battery has been ejected.
ViFly Cam Switcher
Because sometimes two cameras are better than one! Via your Radio transmitter you can switch between two FPV cameras.
Fast Camera Switching (Connecting Receiver Directly)
No matter it is PWM radio receiver on the airplane or the SBUS/IBUS/DSMX radio receiver on racing quad, VIFLY Cam Switcher has the ability to take the signal from both of them via our advanced program. Not like other products to take the racing quad signal through the flight controller, VIFLY Cam Switcher connects the receiver directly that minimizes transition time and gets faster response. It is the time to build your CheaterKwad for more fun.
Easy Setup and no Betaflight Configuration
Though SBUS/IBUS/DSMX radio receivers on racing quad lack PWM channel outputs, VIFLY Cam Switcher can take the signal from the receiver directly through its own algorithm. It doesn’t depend on the flight controller and no need to set the PINIO feature in Betaflight that the setting is very complicated for most of FPV fliers.
Compatible with Racing Quads and Airplanes
VIFLY Cam Switcher is a smart accessory to take the signal from PWM receiver and SBUS/IBUS/DSMX receiver. Now you can easily switch the two cameras on racing drone or RC plane.
Tiny and Lightweight
The size is super small, at only 9x18mm, it’s also a great choice for micro quads and airplanes. The weight is 0.5g that almost has no impact on high performance models.
Torvol Drone Landing Pad
DJI Drone to 5″ Quad, and anything in between, this is your quality landing pad. It can be grounded with the three included plastic pegs, no worries about the wind blowing it while you rip. Whether the terrain is beach sand or grass this keeps your motors and lens free of dirt.
The landing pad conveniently folds into a carrying pouch, which is compact enough to store inside a backpack.
Torvol LiPo Safe Bag – Stealth Edition
Stay safe, organized, and stealth! Now Torvol’s safe bag comes in all black.
Torvol LiPo Safe Bag is made of high quality, fire retardant fabric and a treated polyester shell, giving you the security and ease of mind to take your LiPo batteries with you wherever you want to race. It safely stores up to 15 LiPo’s.
The bag is purposefully designed to perfectly fit inside the Quad PITSTOP Backpack and Quad PITSTOP Backpack PRO, making it the perfect race companion.
Torvol Quad Pitstop Backpack Pro
“A quad backpack” is an understatement! Torvol’s FPV Bestseller: the most trusted racing backpack for professional drone pilots.
* The Torvol Quad PITSTOP Backpack PRO easily carries 4 race quadcopters and all equipment specific to your drone flight; goggles, transmitter, LiPo’s, tools and more.
* It features Torvol’s PITSTOP area. The Torvol smart zipper transforms the backpack into a portable workspace to adjust and modify your drone racing material quickly and effortless.
* This quadcopter backpack includes multiple organizer pockets and dividers which makes it highly customizable. There is ample space for your FPV gears and personal belongings. Larger items like a tripod and a foldable chair can be strapped to the outside.
*The dedicated laptop pocket on the back holds and protects a 15-inch laptop and a charger. An expandable rain cover integrated at the bottom, thick back padding and a hip and sternum strap ensure comfort and convenience while traveling to your race. Torvol’s CLEANSEAT keeps your pants neat on any outdoor space.
*One more extra, you can register on Torvol’s website under “Custom Nametag” to have your own engraved pilot name on it for free!
*LiPo safe pouch not included
Which quads and drones fit inside?
FPV Quadcopters of 6″ and less.
Cinewhoops and Racewhoops of 4″ and less.
DJI drones:
DJI Air 2S, FPV (without propellers), DJI Mini 2/SE, Mavic 2 Pro/Zoom, Mavic 3, Mavic Air, Mavic Air 2, Mavic Mini, Mavic Pro/Pro Platinium, Spark, Tello & Tello Edu.
NO Phantoms.
Autel drones:
Evo Lite, Evo Lite+, Evo Nano, Evo Nano+, Evo I, Evo II, Evo II Pro.
Parrot drones:
Anafi, Anafi Work/Extended/Thermal/FPV/Ai/USA.
Hubsan drones:
Ace Pro/Pro SE, Zino 2 Mini/Mini Pro, H501M, H501A, H501S, H501C, H216A, H502S, H507A, H507D, H502T, H502E, H107D, H111D, H109, H109S, H107C, H111C Nano, H122D, H123D.
NO Zino, Zino 2.
Yuneec drones:
Typhoon H, Mantis Q, Typhoon H3
Besides these brands, most drones on the market fit inside the Pitstop Pro.
Torvol Quad Pitstop Backpack Pro – Stealth Edition
“A quad backpack” is an understatement! Torvol’s FPV Bestseller: the most trusted racing backpack for professional drone pilots now in Stealth Edition!
* The Torvol Quad PITSTOP Backpack PRO easily carries 4 race quadcopters and all equipment specific to your drone flight; goggles, transmitter, LiPo’s, tools and more.
* It features Torvol’s PITSTOP area. The Torvol smart zipper transforms the backpack into a portable workspace to adjust and modify your drone racing material quickly and effortless.
* This quadcopter backpack includes multiple organizer pockets and dividers which makes it highly customizable. There is ample space for your FPV gears and personal belongings. Larger items like a tripod and a foldable chair can be strapped to the outside.
*The dedicated laptop pocket on the back holds and protects a 15-inch laptop and a charger. An expandable rain cover integrated at the bottom, thick back padding and a hip and sternum strap ensure comfort and convenience while traveling to your race. Torvol’s CLEANSEAT keeps your pants neat on any outdoor space.
*One more extra, you can register on Torvol’s website under “Custom Nametag” to have your own engraved pilot name on it for free!
*LiPo safe pouch not included
Which quads and drones fit inside?
FPV Quadcopters of 6″ and less.
Cinewhoops and Racewhoops of 4″ and less.
DJI drones:
DJI Air 2S, FPV (without propellers), DJI Mini 2/SE, Mavic 2 Pro/Zoom, Mavic 3, Mavic Air, Mavic Air 2, Mavic Mini, Mavic Pro/Pro Platinium, Spark, Tello & Tello Edu.
NO Phantoms.
Autel drones:
Evo Lite, Evo Lite+, Evo Nano, Evo Nano+, Evo I, Evo II, Evo II Pro.
Parrot drones:
Anafi, Anafi Work/Extended/Thermal/FPV/Ai/USA.
Hubsan drones:
Ace Pro/Pro SE, Zino 2 Mini/Mini Pro, H501M, H501A, H501S, H501C, H216A, H502S, H507A, H507D, H502T, H502E, H107D, H111D, H109, H109S, H107C, H111C Nano, H122D, H123D.
NO Zino, Zino 2.
Yuneec drones:
Typhoon H, Mantis Q, Typhoon H3
Besides these brands, most drones on the market fit inside the Pitstop Pro.
Torvol Urban Backpack
Torvol’s Urban Backpack is a stylish, sleek-looking quad backpack developed by the Pilots Collective – namely @jedeyefpv, @ummagawd, and @stingersswarm.
Features a low profile look and the capacity that you’ve come to expect from Torvol products. As with all Torvol, made with high quality materials.
Whether you’re strolling in the city or having a quick session, you’re ready with the Urban Backpack!
ToolkitRC M7 Multifunctional Balance Charger 200W DC 10A 2-6S
ToolkitRC M7 Multifunctional Balance Charger 200W DC 10A 2-6S
Specifications:
CHARGER
OUTPUT
MEASURER
Included:
CellMeter 8 V2.0 Multifunction 2-8S Battery Tester
Calling it a battery tester is an understatement! This CellMeter 8 V2 is a multifunctional device allowing you to check a battery’s voltage, balance a battery, discharge a battery, and even test a servo.
TBS Tango 2 FPV Radio Controller Transmitter
The Tango 2 is released as the smaller radio available, yet it comes with full sized Hall gimbals, Freedom TX (temporary OpenTX fork), and the lowest latency of any TX system.
Team BlackSheep has been at the forefront of perfecting the interface between FPV drone and mind. The TBS Tango 2 changes how radio remote controls will be from here on out! Despite being the smallest remote control available, it comes with full size HAll gimbals, full-featured FreedomTX (temporary OpenTX fork), the lowest end-to-end latency of any remote and transmission system, unbreakable 3 & 2-position switches, open source operating system, built-in battery, USB-C charging, and so much more! It’s not just a retouched game controller, it was designed from the ground up for R/C! The form factor and features make it the ideal take-anywhere, fly-anytime remote control.
CROSSFIRE Built in
The first radio with TBS Crossfire built in. This significantly lowers your cost, increases reliability and minimizes set up time. And the cherry on top are the LUA scripts being part of the familiar user interface. The antenna swivels out of the way, or doubles as a kick-stand when resting. TBS Cloud ready to go from the start. It all just makes sense.
Happymodel Mobula6 HDZero 1S 65mm Micro Whoop
The wait is over, the world’s first HDZero 65mm Whoop is here! The Mobula6 is a smooth and agile brushless drone that incorporates the HDZero Nano Lite Camera for a weight of 23.5 grams. Happymodel teamed up with HDZero, Runcam, Nick Burns, Mr. Shutterbug, Ryan Quellet, and many other enthusiasts to make this a reality.
*This is the ELRS version
*Batteries not included
Happymodel DiamondF4 ELRS 5-in-1 AIO FC 2.4GHz
Happymodel’s AIO triangle-shaped whoop board! The Diamond F4 5-in-1 AIO board makes building whoops easy as picking your camera, motors, and frame.
*Direct replacement AIO for the Moblite6/Moblite 7 whoops
*ELRS Version
Happymodel SuperbeeF4 Lite AIO 1S FC 2.4GHz ELRS
The direct replacement AIO board for the Mobula6 HDZero. The default OSD is set to “MSP” since this is considered spare part for the Mobula6 HDZero.
If using this board with an analog camera you will need to change some settings in BetaFlight. Instructions can be found at SuperbeeF4
* ELRS version
Happymodel X2 AIO F4 Flight Controller SPI ELRS RX 2-4S 12A ESC
The Happymodel ELRS X2 AIO Flight Controller is the direct replacement for the Mobula7 HDZero.
It comes with an integrated SPI 2.4GHz ELRS receiver and 12A Blheli_S ESC which supports 2-4S batteries. Bigger mosfet supports high to 12A currents and would be better for a 2-4S toothpick drone or long-range FPV drone. The 2.4GHz ExpressLRS receiver is equipped with the SX1280 radio frequency chip with high sensitivity, high packet rate, and low latency. Featuring an MPU 6000 SPI sensor and OSD, this board is the perfect addition to your FPV build.
Happymodel Pancake 2-6S F4 AIO Flight Controller SPI ELRS RX + 5.8GHz OpenVTX
Happymodel Pancake 2-6S F4 AIO Flight Controller SPI ELRS RX + 5.8GHz OpenVTX
The Pancake AIO was designed with the help of the ExpressLRS team. It features an onboard 2.4GHz ELRS SPI receiver as well as a 5.8 GHz OpenVTX with up to 400mw of power. It can be mounted using the 30.5mm or 20mm spaced holes.
DJI FPV Air Unit
Yes, the original DJI Air Unit! This 5.8Ghz air unit (FPV camera + VTX) provides amazing visual clarity that is able to be transmitted to your DJI Goggles through its built-in receiver module. The DJI FPV Air Unit provides ultra-low latency HD digital image transmission, built-in 1080p/60fps DVR recording, and eight frequency channels to allow up to eight pilots to fly simultaneously.
Digital HD systems have traditionally been rather bulky and unwieldy to mount on a mini quad. Not anymore. With this air unit, you can comfortably fit the module in your mini quad stack. The ‘mini’ camera fits easily into your existing builds, no weird mounting adapters.
Note: The air unit module does get very hot in use. Do not power on for an extended period of time without proper cooling or flying.
GEPRC Mark5 HD 4S Quad w/Nebula Camera ELRS 2.4GHz version
The Mark5 is considered by many enthusiasts to be amongst the top freestyle quadcopters on the market. It is a stable, durable, and perfectly structured freestyle quad that features the Caddx Nebula Camera for an HD experience. The MARK5 is developed specifically for freestyle with a squashed X arm design. The unique shock absorbing structure design, fewer vibrations, and resonance provides a stable operating environment for the electronic system. Aluminum alloy side plates not only look stunning but reduce weight and add more endurance. MARK5 is equipped with GEPRC’s latest SPAN F722-HD-BT FC with high performance and lots of ports, supporting Bluetooth wireless connection for easy field tuning. Freshly upgraded SPAN G50A BLHeli_32 4IN1 50A ESC with GEPRC’s latest 2107.5 motors, has great explosive power and very fast response speed. The new GEMFAN Freestyle 4S propellers provide a delicate and silky smooth flight experience. The MARK5 is shipped with two different 3D printed action cam mounts that can be fitted with GoPro8/9/10, Naked GoPro8, Insta 360 GO2, and Caddx Peanut cameras.
After continuous testing and tuning by the GEPRC R&D team, this is yet another GEPRC drone that comes perfectly tuned right out of the box. Just take it out, plug in the battery and have fun!
Tattu R-Line Version 4.0 4S 1550mAh 14.8V 130C Lipo Battery XT60 Plug
Tattu R-Line Version 4.0 4S 1550mAh 14.8V 130C Lipo Battery XT60 Plug
Tattu has a reputation for making reliable and powerful batteries and is a top choice for many racers, freestylers, and professionals alike.
R-Line is Tattu’s flagship series! R-Line batteries are formulated to provide maximum power throughout the discharge cycle of the battery. With other batteries, you’ll feel the battery voltage sag after 30 seconds – not with the R-Lines. Experience the difference for yourself!
Flywoo Explorer 4″ LR V2.2 w/ Caddx Polar Vista HD and 2.4 GHz ELRS
Flywoo Explorer 4″ LR V2.2 w/ Caddx Polar Vista HD and 2.4 GHz ELRS
The Flywoo Explorer Long Range Quad is in a new category of quad known as “#MicroLongRange,” which was created by Dave_C FPV in collaboration with Flywoo. Micro Long Range quadcopters allow fpv pilots to get incredible HD footage, all while capturing incredible footage at high speeds! This type of quad is great as a cruiser.
Walksnail Avatar Digital HD FPV Goggles v1
Avatar HD Micro Camera/VTX Kit features a micro-sized digital camera and VTX that works with HD Goggles such as the Avatar and Fat Shark HD Dominator.
Note: This is the Flywoo rebranded. It doesn’t include the original walksnail packaging or the original walksnail antenna. Equipped with Top Circular Polarized Flywoo double antennas.
Flywoo Explorer 750mAh 4S 80c 15.2V HV LiPo Battery (2 pcs)
The Flywoo Explorer 80c 4S 450mAh Battery is a high-quality HV battery that battery weighs 55.2g. This battery is perfect for Micro Whoops and H-Frame quads.
Explorer series batteries are specially designed for long flight time and all are high voltage battery. Using this battery will give you a significant increase in flight time as well as a bit more power over the stock battery.
Walksnail Avatar HD Micro Camera/VTX Kit (19mm x 19mm)
The Walksnail Avatar Digital HD FPV Goggles feature high-fidelity Full HD OLED displays and support a new 1080p video transmission protocol in a compact design.
This FPV Drone goggle features high fidelity FullHD OLED displays and supports a new 1080p video transmission protocol in a compact design. A wide range of IPD and focus adjustments allows the user to tune the optics for either eye. The Avatar Digital HD FPV Goggles is packed with premium features such as USB-C Video out, HD DVR recording, and an intuitive full-color graphic user interface. Support for Betaflight Canvas Mode puts you in control of the on-screen display. The Avatar is the new standard for premium FPV!
Recommendation for you
Happymodel Mobeetle6 65mm – ELRS version
Happymodel’s new Mobeetle6 BNF is the lightest 65mm mass produced whoop in the world! The DiamondF4 Flight controller and 0702 motors were inspired from Angry Don FPV. A whoop style 65mm that includes a freestyle frame so you can fly as you prefer!
Happymodel Crux 35 HDZero 3.5″ Quad – ELRS version
CRUX35 HDZero is an ultra-lightweight 3.5Inch FPV Freestyle FPV Racing Drone, the weight of the whole drone is only 108g for the digital HD version. The Crux35 uses Happymodel EX1404 high-efficiency motor and HQPROP 3.5-inch three-blade propeller to ensure the largest thrust-to-weight ratio under the most efficient premise, which can bring you a smooth Freestyle flying experience.
This HDZero version is equipped with Runcam Nano Camera and the HDZero Whoop VTX.
This receiver version is the SPI ExpressLRS.
ExpressLRS is the most popular RC link system.
NOTICE: ELRS SPI Version is updated to ExpressLRS v2.0 version
Flywoo Firefly 1S Nano Baby Quad 40mm V1.2 (Deadcat style frame) ELRS
Flywoo Firefly 1S Nano Baby Quad 40mm V1.2 (Deadcat style frame) ELRS
Firefly 1S Nano Baby Quad is an 20g ultralight 1S Quad best for freestyle and crusing. Pilots can enjoy up to 8 minutes and 45 seconds flight time with Flywoo’s latest 1S 450mah battery ! Through a lot of tests, Flywoo has found the best configuration for Firefly 1S nano baby quad!Suitable for cruising super long flight time or ripping freestyle!
Last but not least, it is very quiet, like a mosquito, suitable for both indoors and outdoors.
** IMPORTANT NOTE:
Please do not try to update the ESC firmware as it may cause damage.
**Default ESC firmware: O_H_5_REV16_8-48K
Main Changes to V1.2 :
Modified the design of the bottom plate. The structure of the bottom plate is more reasonable and stronger . The battery can be placed either horizontally or vertically.
Upgraded to GNB27 V2 connectors for better current flow from battery . ( Note: GNB27 V2 is very tight, but it will become more suitable after a few uses.)
Flywoo Explorer 1S 450mAh 80C Battery 4.35v GNB27 V2 (4 pack)
Flywoo Explorer series batteries are specially designed for long flight time and all are high voltage battery. Using this battery will give you a significant increase in flight time as well as a bit more power over the stock battery.
Fat Shark Scout HD FPV Goggles
The Scout HD was Fat Shark’s first HD digital FPV goggle and the result was spectacular! Unparalleled image quality is achieved with a 1080p display viewed through Fat Shark’s patented folded optical engine. The 3.5” panel delivers a crisp 44-degree FOV image at 60 fps with compatibility with Shark Byte transmitters. Scout retains a reputation as a high-performance goggle at an affordable price while maintaining anti-fog fan features, comfortable form factor, and glasses accommodating faceplate.
Gemfan 1610-2 40mm (1.5mm Shaft) Propeller (4 pack)
A 40mm bi-blade prop from Gemfan. These are a fit on popular quads such as the Happymodel 1S Mobula 7/ Mobula 7 HD, Moblite7 HDZero 1s, and others with a 1.5mm center hole with prop length of 40mm.
Happymodel ES24TX Slim Pro ELRS TX Module
This Slim Pro TX module is designed by Happymodel and based on the open source- ExpressLRS which is a very popular low latency and high packet rate RF module for RC Airplane and FPV Racing drone. Its main hardware architecture is ESP32, ESP8285 and SX1280 RF chip. The ES24TX Slim Pro module is a complete solution which is already pre-loaded with the Expresslrs firmware and it’s plug and play for Frsky X-lite/X-lite pro/X9 Lite , TBS Tango2.
This Slim Pro module comes with an aluminum alloy shell and is equipped with a cooling fan that automatically works when the module is working at 250mw.
The slim pro TX module supports a maximum power output of about 1000mw, this would be very useful for Long Range FPV.
Happymodel Mobula7 1S 75mm Whoop – ELRS version
It’s always Whoop Season! This is one of your best options for a 75mm. You get unbelievable video range from the 400mw vtx. The new RS0802 motors come with a new unibell design using a 1.5mm shaft. Performs with nice precision.
ELRS version
Happymodel ELRS 2G4 Whoop Flight Controller
The world’s first AIO 5in1 F4 flight controller with integrated SPI 2.4GHz ExpressLRS receiver has been launched. The flight controller integrates SPI controlled 2.4GHz ExpressLRS receiver, Dshot protocol 4-in-1 ESC, 5.8GHz 40ch video transmitter and Betaflight OSD. Ultra-small size and ultra-stable remote control range can improve the range of the original SPI receiver. And because the 2.4GHz ExpressLRS receiver is equipped with the SX1280 radio frequency chip with high sensitivity, high packet rate and low latency, this flight controller is the one that all Race/Freestyle pilots needed. It is suitable for use in Tiny whoop Race or Toothpick Freestyle, and can also be used in 1S ultra-lightweight Nano Long Range platform.
HappyModel EP2 2.4GHz RX ELRS Receiver
Happymodel’s 2.4GHz ELRS nano series receiver with tiny ceramic antenna.
The PP RX was designed by @Jye Smith from the ExpressLRS development team. Its main hardware architecture is STM32L432KBU6 MCU and SX1280 RF chip. It has a built-in ceramic antenna, which is super light and small in size.
On the basis of that PP RX, Happymodel has developed the Nano 2.4GHz RX of ESP8285 version named EP1 and EP2. The RF module of EP1/EP2 is the same as PP RX and uses ESP8285 MCU. You can upgrade firmware via WiFi!
Due to the low-latency and high-refresh-rate RF module, they are very comfortable for FPV race and Long Range FPV. These are very suitable for Tiny Whoops because of the ultra-light and Nano size!
Note: This is the EP2 RX Version
Happymodel Mobula 7 1S 75mm HD recording Whoop – ELRS version
Happymodel continues to innovate with this 75mm whoop that can record in 1080 HD and features an on-board blackbox for gyroflow functionality.
Features X12 AIO board and a 400mw vtx. You’ve seen the reviews!
ELRS version
Happymodel X12 1-2S AIO Whoop F4 Flight Controller 12A ESC – ELRS version
Happymodel X12 1-2S AIO Whoop F4 Flight Controller 12A ESC – ELRS version
Happymodel X12 is a 5-in-1 AIO board featuring an F4 Flight Controller. It has an onboard 12A 4-in-1 ESC, 5.8GHz OpenVTX, with ELRS. This AIO has nice 400mw range great for any brushless whoop.
Happymodel EP82 VRX-Backpack Module
So what is this VRX backpack? This Happymodel “backpack”is designed to allow wireless communication between ExpressLRS, and other FPV-related devices for command and control, or for querying config. Currently there aren’t many VRX modules that can allow them to communicate with ELRS. This small ESP-based receiver can be “piggybacked” onto your VRX module, which allows ExpressLRS to control the band and channel that your goggles are set to. We call this device the “VRX-Backpack”.