Happymodel ELRS 2G4 Whoop Flight Controller
Out of stock
The world’s first AIO 5in1 F4 flight controller with integrated SPI 2.4GHz ExpressLRS receiver has been launched. The flight controller integrates SPI controlled 2.4GHz ExpressLRS receiver, Dshot protocol 4-in-1 ESC, 5.8GHz 40ch video transmitter and Betaflight OSD. Ultra-small size and ultra-stable remote control range can improve the range of the original SPI receiver. And because the 2.4GHz ExpressLRS receiver is equipped with the SX1280 radio frequency chip with high sensitivity, high packet rate and low latency, this flight controller is the one that all Race/Freestyle pilots needed. It is suitable for use in Tiny whoop Race or Toothpick Freestyle, and can also be used in 1S ultra-lightweight Nano Long Range platform.
$57.99
Out of stock
Specifications:
-
- MCU: STM32F411CEU6
- Gyro:Â ICM20689
- Input Voltage: 1S (2.9-4.35V)
- Firmware Target: CRAZYBEEF4SX1280
Onboard ESC:
-
- MCU: EFM8BB21
Input Voltage: 1S (2.9-4.35V)
-
- Current: 5A continuous peak 6A (3 seconds)
- Factory firmware: O_H_5_REV16_8.HEX
- Default protocol: DSHOT600
Onboard 2.4GHz ExpressLRS Receiver:
-
- Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RFÂ Frequency: 2.4GHzAntenna : SMD antenna
Telemetry output Power: 12dBmReceiver protocol: SPI ExpressLRSCould bind with Happymodel ES24TX , ES24TX Lite, ES24TX Slim and DIY 2.4GHz ELRS TX module(need to flash the same version ELRS firmware)
Onboard 5.8HGz VTX:
-
-
- Output power: 25-200mw switchable
- Frequency:Â 5.8GHz 5bands 40 channels(include Race band) Smart audio ready
- Current consumption: 300mA
Included:
- 1x HappyModel ELRS 2G4 Whoop Flight Controller
-
Based on 0 reviews
Only logged in customers who have purchased this product may leave a review.
Related products
-
Category Name, Electronics, Flight Controllers
Happymodel CrossF4 F411 1-2S 5A AIO Whoop Flight Controller with UART ELRS v3.0 receiver – ELRS 2.4gHz
Category Name, Electronics, Flight ControllersHappymodel CrossF4 F411 1-2S 5A AIO Whoop Flight Controller with UART ELRS v3.0 receiver – ELRS 2.4gHz
HappyModel keeps them coming! Now with yet another fantastic whoop AIO. The HappyModel CrossF4 1-2S AIO Whoop Flight Controller (F4 FC / 5A 4in1 ESC) – Featuring F411 Flight Controller, with a built in serial UART ELRS for V3.0.
NOTE:Â Onboard blackbox enable method:
-Type the following command to CLI:
-set blackbox_device = SPIFLASH
-set flash_spi_bus = 2
-resource FLASH_CS 1 a14Pay attention: Bind procedure is the same like Happymodel EP1/EP2 receiver, as you need to upgrade your ExpressLRS TX module to V3.X version first.
Alternative-Binding-Method-for-UART-Based-ELRS-RX
Onboard blackbox enable method:
Type the following command to CLI:
set blackbox_device = SPIFLASH
set flash_spi_bus = 2
resource FLASH_CS 1 a14
saveSKU: HM.CROSSF.FC.ELRS -
Electronics, ELRS Receivers
HappyModel EP2 2.4GHz RX ELRS Receiver
Happymodel’s 2.4GHz ELRS nano series receiver with tiny ceramic antenna.
The PP RX was designed by @Jye Smith from the ExpressLRS development team. Its main hardware architecture is STM32L432KBU6 MCU and SX1280 RF chip. It has a built-in ceramic antenna, which is super light and small in size.
On the basis of that PP RX, Happymodel has developed the Nano 2.4GHz RX of ESP8285 version named EP1 and EP2. The RF module of EP1/EP2 is the same as PP RX and uses ESP8285 MCU. You can upgrade firmware via WiFi!
Due to the low-latency and high-refresh-rate RF module, they are very comfortable for FPV race and Long Range FPV. These are very suitable for Tiny Whoops because of the ultra-light and Nano size!Note: This is the EP2 RX Version
SKU: HM.EP2.RX.ELRS. -
Electronics, Flight Controllers
Happymodel DiamondF4 ELRS 5-in-1 AIO FC 2.4GHz
Happymodel’s AIO triangle-shaped whoop board! The Diamond F4 5-in-1 AIO board makes building whoops easy as picking your camera, motors, and frame.
*Direct replacement AIO for the Moblite6/Moblite 7 whoops
*ELRS Version
SKU: HM.DIAMF4.FC.ELRS.
There are no reviews yet.