Happymodel Pancake 2-6S F4 AIO Flight Controller SPI ELRS RX + 5.8GHz OpenVTX
The Pancake AIO was designed with the help of the ExpressLRS team. It features an onboard 2.4GHz ELRS SPI receiver as well as a 5.8 GHz OpenVTX with up to 400mw of power. It can be mounted using the 30.5mm or 20mm spaced holes.
$40.99 $47.99
Features:
- 30.5 x 30.5mm or 20x20mm Mounting Pattern
- ONBOARD SPI EXPRESSLRS 2.4GHZ
- ONBOARD 5.8GHZ OPENVTX
- CRAZYBEEF4SX1280 FC
- 2-S6S Lipo Input
- Betaflight OSD
- MPU 6000 SPI
- 48 Channels
Specifications:
FLIGHT CONTROLLER
- Firmware Target: CRAZYBEEF4SX1280
- MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
- Sensor: MPU6000 (SPI connection)
- Mount hole type: 20×20mm or 30.5×30.5mm
- Power supply: 2-6S battery input
- Built-in Betaflight OSD(SPI Control)
- Built-in 5.8G OpenVTX 0mw~400mw
- Built-in ExpressLRS 2.4G ELRS V2.0 firmware compatible
- Weight: 5.18 g
ONBOARD SPI EXPRESSLRS 2.4GHZÂ
- Â Receiver Packet Rate option: 50Hz/150Hz/250Hz/500Hz
- Support ExpressLRSÂ v2.0 or latest*
- RF Frequency: 2.4GHz
- Antenna: SMD ceramic antenna
- Telemetry output Power:Â <12dBm
- Receiver protocol:Â SPI ExpressLRS
- Compatible with ExpressLRS V2.0 TX Module
ONBOARD 5.8GHZ OPENVTX
- Firmware:Â OpenVTX
- Smartaudio v2.1
- PIT Mode support
- RCE Mode support
- Channels: 48ch
- Transmitting Power:Â 0/RCE/25mw/100mw/400mw
- Power supply:Â DC 5V
- Current (5v): <650ma (400mw)
- Antenna connector:Â U.FL
** IMPORTANT NOTE: ExpressLRS firmware cannot be flashed separately
Included:
- 1 x Pancake AIO Flight Controller
- 1 x XT60 Pigtail
- 1 x Mounting Hardware
- 1 x Ufl Antenna
- 1 x Wiring Harness
Based on 0 reviews
Only logged in customers who have purchased this product may leave a review.
Related products
-
-
Category Name, Electronics, ELRS Receivers
RadioMaster RP3 2.4GHz ELRS Diversity Receiver v2
The RadioMaster RP series of receivers are designed with size, ease of use, and range in mind. Utilizing ExpressLRS 2.4ghz Open-source firmware the RP series of nano receivers deliver features and range today’s pilots have come to expect.
Developed around the ESP8285 MCU and SX1280IMLTRT RF Chip the RP series offer Lora and FLRC 2.4ghz RF links offering incredible range and low latency. With Wifi built-in, firmware updates can be done on your craft without the need to remove the receiver. Binding can be done using a bind phrase meaning no more bind plugs or fiddly button presses while trying to plug in your battery.
The RP3 receiver features a Skyworks SE2431L providing an LNA for improved receiver performance, a PA providing up to 100mw of telemetry performance, and antenna switching for antenna diversity.
Features:
- Optimized PCB design for better heat dissipation.
- LNA for better receiver range.
- PA for better telemetry range.
- Antenna Diversity for improved signal stability and range.
SKU: RM.RP3.RX.ELRS.V2. -
-
Category Name, Electronics, ELRS Receivers
Happymodel EP1 2.4GHz RX ELRS Receiver
The PP RX is designed by @Jye Smith from ExpressLRS development team. Its main hardware architecture is STM32L432KBU6 MCU and SX1280 RF chip. On the basis of PP RX, we have developed the Nano 2.4GHz rx of ESP8285 version named EP1 and EP2. The RF module of EP1/EP2 is the same like PP RX and use ESP8285 MCU . So you can upgrade firmware by WIFI , that’s too simple. Due to the low-latency and high-refresh-rate RF module, they are very comfortable for FPV race and Long Range FPV. And very suitable for whoop because of the ultra light and Nano size.
SKU: HM.EP1.RX.ELRS.
There are no reviews yet.