Flight Controllers
Showing all 13 results
-
-
-
Category Name, Electronics, Flight Controllers
DarwinFPV FPVCycle Whoop Stack Flight Controller 6S 45A ESC
Category Name, Electronics, Flight ControllersDarwinFPV FPVCycle Whoop Stack Flight Controller 6S 45A ESC
This is a unique stack for the demands of the industry today. It has a 25.5×25.5 M2 (Whoop) mount pattern because there are now many frames that are designed with that pattern. This stack can be used for everything from 3″ to 6″.
We split the ESC and FC but called for the ESC to have a nearly empty top side and the FC to have nearly all it’s components on the bottom and sit inside the footprint of the ESC solder pads. ALL of the FC’s solder pads are also on the TOP. When you assemble the stack inside your frame, you will be able to access and solder ALL pads on BOTH boards. Additionally, the FC has a black box chip which is rare on AIO boards.
SKU: DF.CYCLE.STACK.45A. -
Category Name, Electronics, Flight Controllers
Flywoo GOKU GN 405S 40A AIO (MPU6000 ) 25.5 X 25.5
Flywoo’s new top GOKU series AIO are finally here! GOKU GN405 40A FC is an economical and durable all-in-one AIO , which can meet most your FPV needs.
Use powerful F405 chip , integrate 5V BEC, barometer, black box, WS2812LED, support 6 complete hardware serial ports, I2C and other functions are all open.SKU: FW.GOKU.405S.AIO. -
-
Category Name, Electronics, Flight Controllers
Happymodel CrossF4 F411 1-2S 5A AIO Whoop Flight Controller with UART ELRS v3.0 receiver – ELRS 2.4gHz
Category Name, Electronics, Flight ControllersHappymodel CrossF4 F411 1-2S 5A AIO Whoop Flight Controller with UART ELRS v3.0 receiver – ELRS 2.4gHz
HappyModel keeps them coming! Now with yet another fantastic whoop AIO. The HappyModel CrossF4 1-2S AIO Whoop Flight Controller (F4 FC / 5A 4in1 ESC) – Featuring F411 Flight Controller, with a built in serial UART ELRS for V3.0.
NOTE: Onboard blackbox enable method:
-Type the following command to CLI:
-set blackbox_device = SPIFLASH
-set flash_spi_bus = 2
-resource FLASH_CS 1 a14Pay attention: Bind procedure is the same like Happymodel EP1/EP2 receiver, as you need to upgrade your ExpressLRS TX module to V3.X version first.
Alternative-Binding-Method-for-UART-Based-ELRS-RX
Onboard blackbox enable method:
Type the following command to CLI:
set blackbox_device = SPIFLASH
set flash_spi_bus = 2
resource FLASH_CS 1 a14
saveSKU: HM.CROSSF.FC.ELRS -
Electronics, Flight Controllers
Happymodel DiamondF4 ELRS 5-in-1 AIO FC 2.4GHz
Happymodel’s AIO triangle-shaped whoop board! The Diamond F4 5-in-1 AIO board makes building whoops easy as picking your camera, motors, and frame.
*Direct replacement AIO for the Moblite6/Moblite 7 whoops
*ELRS VersionSKU: HM.DIAMF4.FC.ELRS. -
Electronics, Flight Controllers
Happymodel ELRS 2G4 Whoop Flight Controller
The world’s first AIO 5in1 F4 flight controller with integrated SPI 2.4GHz ExpressLRS receiver has been launched. The flight controller integrates SPI controlled 2.4GHz ExpressLRS receiver, Dshot protocol 4-in-1 ESC, 5.8GHz 40ch video transmitter and Betaflight OSD. Ultra-small size and ultra-stable remote control range can improve the range of the original SPI receiver. And because the 2.4GHz ExpressLRS receiver is equipped with the SX1280 radio frequency chip with high sensitivity, high packet rate and low latency, this flight controller is the one that all Race/Freestyle pilots needed. It is suitable for use in Tiny whoop Race or Toothpick Freestyle, and can also be used in 1S ultra-lightweight Nano Long Range platform.
SKU: HM.2G4.FC.ELRS. -
Electronics, Flight Controllers
Happymodel Pancake 2-6S F4 AIO Flight Controller SPI ELRS RX + 5.8GHz OpenVTX
Electronics, Flight ControllersHappymodel Pancake 2-6S F4 AIO Flight Controller SPI ELRS RX + 5.8GHz OpenVTX
The Pancake AIO was designed with the help of the ExpressLRS team. It features an onboard 2.4GHz ELRS SPI receiver as well as a 5.8 GHz OpenVTX with up to 400mw of power. It can be mounted using the 30.5mm or 20mm spaced holes.
SKU: HM.PANCAK.FC.ELRS. -
Electronics, Flight Controllers
Happymodel SuperbeeF4 Lite AIO 1S FC 2.4GHz ELRS
The direct replacement AIO board for the Mobula6 HDZero. The default OSD is set to “MSP” since this is considered spare part for the Mobula6 HDZero.
If using this board with an analog camera you will need to change some settings in BetaFlight. Instructions can be found at SuperbeeF4
* ELRS version
SKU: HM.SPBEF4.FC.ELRS. -
Electronics, Flight Controllers
Happymodel X12 1-2S AIO Whoop F4 Flight Controller 12A ESC – ELRS version
Electronics, Flight ControllersHappymodel X12 1-2S AIO Whoop F4 Flight Controller 12A ESC – ELRS version
Happymodel X12 is a 5-in-1 AIO board featuring an F4 Flight Controller. It has an onboard 12A 4-in-1 ESC, 5.8GHz OpenVTX, with ELRS. This AIO has nice 400mw range great for any brushless whoop.
SKU: HM.X12.FC.ELRS. -
Electronics, Flight Controllers
Happymodel X2 AIO F4 Flight Controller SPI ELRS RX 2-4S 12A ESC
The Happymodel ELRS X2 AIO Flight Controller is the direct replacement for the Mobula7 HDZero.
It comes with an integrated SPI 2.4GHz ELRS receiver and 12A Blheli_S ESC which supports 2-4S batteries. Bigger mosfet supports high to 12A currents and would be better for a 2-4S toothpick drone or long-range FPV drone. The 2.4GHz ExpressLRS receiver is equipped with the SX1280 radio frequency chip with high sensitivity, high packet rate, and low latency. Featuring an MPU 6000 SPI sensor and OSD, this board is the perfect addition to your FPV build.
SKU: HM.X2F4.FC.ELRS.