Radio Accessories
Showing all 5 results
-
Radio Accessories, Radio Transmitters
Happymodel ES24TX Slim Pro ELRS TX Module
This Slim Pro TX module is designed by Happymodel and based on the open source- ExpressLRS which is a very popular low latency and high packet rate RF module for RC Airplane and FPV Racing drone. Its main hardware architecture is ESP32, ESP8285 and SX1280 RF chip. The ES24TX Slim Pro module is a complete solution which is already pre-loaded with the Expresslrs firmware and it’s plug and play for Frsky X-lite/X-lite pro/X9 Lite , TBS Tango2.
This Slim Pro module comes with an aluminum alloy shell and is equipped with a cooling fan that automatically works when the module is working at 250mw.
The slim pro TX module supports a maximum power output of about 1000mw, this would be very useful for Long Range FPV.SKU: HM.ES24TX.SLIM.ELRS. -
-
Category Name, Radio Accessories, Radio Transmitters, RadioMaster
RadioMaster 4IN1 2.4GHz Micro Nano/JR Transmitter Module
Category Name, Radio Accessories, Radio Transmitters, RadioMasterRadioMaster 4IN1 2.4GHz Micro Nano/JR Transmitter Module
The RadioMaster 4IN1 External Nano/JR Module, which is a multi-protocol module that integrates CC2500, NRF24L01, A7105 and CYRF6936 RF chips. This is external nano module can also be used on JR modules, with the included JR adapter.
RM 4IN1 is compatible with more than 70 RF protocols, including DSMX, Flysky, SFHSS, HiTec, HoTT, OMP, Radiolink, Frsky and many more.  The module features a +20dBm RF gain, a 2.4GHz frequency band, and an operational voltage of 4.5-8.4V.
Designed for OpenTX and EdgeTX systems, the RM 4IN1 module allows the radio to connect with most mainstream protocols on the market. Though when this module is used in conjunction with a suitable EdgeTX or OpenTX compatible radios such as the TX16s, TX12 or Zorro, the RM 4in1 module can be used as a wireless trainer link to a student radio such as another TX16s, TX12, Zorro or any other radio capable of transmitting DSMX, Frsky or Flysky protocols.
SKU: RM.4IN1.MODULE. -
Radio Accessories, Radio Transmitters
RadioMaster Lubricant Set for Gimbals
RadioMaster’s lubricant and grease will have your gimbals feeling brand new. Your radio has been good to you, treat it right!
Use the damping oil for a silky smooth dampening effect on your throttle tension bar. Use the lubricating oil for gimbal bearings and moving parts.
SKU: RM.GIMLUB.LUBRIC. -
Radio Accessories, Radio Transmitters, TBS
TBS Tango 2 Module Bay Add-On
This is an after-market mod to add a module bay to your Tango 2. The module bay sticks to the back of your Tango 2 and plugs into the receptacle board of your Tango 2.
Installation process
- Install the FPC cable to the PCB.
With the blue side facing up, lift the lock and slide the cable in then lock it down. - Feed the cable through the bottom and place the PCB to the module bay.
- Turn the module bay around to make sure everything fits accordingly.
- Close the case with the 2 screws provided
- Use a dremel, knife or solder tip to cut a small hole accoridng to the outline.
- Slide the flex PCB through the drilled case.
- Clean the back surface and tape the Tango 2 module bay down
- Â Install the FPC cable into the receptacle.
- Close the Tango2 case, and you’re done!
*IMPORTANT NOTE
*The first batch of Tango 2 shipped WITHOUT module bay capability. Please verify that there is a connector (in pictures above) before purchasing this add-on. Upgrade PCB’s can also be purchased!
Also, whenever opening up your Tango 2 in future, you will need to open the module bay and release the flex PCB from the socket.*We have discovered that XJT mini modules are using a pin that we did not anticipate for use in our module bay. It appears that the XJT mini module is the only module on the market that uses this pin.
Due to a hardware incompatibility between the XJT mini module and the Tango 2 (V2 and up) boards, the Tango 2 will NOT be able to support the XJT mini module.
SKU: TBS.T2ModB - Install the FPC cable to the PCB.