HappyModel EP2 2.4GHz RX ELRS Receiver
Happymodel’s 2.4GHz ELRS nano series receiver with tiny ceramic antenna.
The PP RX was designed by @Jye Smith from the ExpressLRS development team. Its main hardware architecture is STM32L432KBU6 MCU and SX1280 RF chip. It has a built-in ceramic antenna, which is super light and small in size.
On the basis of that PP RX, Happymodel has developed the Nano 2.4GHz RX of ESP8285 version named EP1 and EP2. The RF module of EP1/EP2 is the same as PP RX and uses ESP8285 MCU. You can upgrade firmware via WiFi!
Due to the low-latency and high-refresh-rate RF module, they are very comfortable for FPV race and Long Range FPV. These are very suitable for Tiny Whoops because of the ultra-light and Nano size!
Note: This is the EP2 RX Version
$13.50
Specifications:
- Frequency Range: 2400 MHz to 2500 MHz
- Maximum receive refresh rate: 500Hz
- RF Chip: SX1280IMLTRT RF Module
- Minimum receiver refresh rate: 25Hz
- Antenna: SMD Ceramic antenna
- Dimension: 10mm*10mm*6mm
- Firmware Target:Â aec8ad82
- MCU: ESP8285 MCU
- Firmware Upload: WiFi
- Working voltage: 5v
- Weight: 0.44gram
- Peak gain: 3.7dB
- Type: ISM
- Pre-installed ELRS V3.0.1
Included:
- Happymodel ExpressLRS Nano 2.4GHz EP2 RX x 1
- Clear Plastic Heat Shrink x 1
Based on 0 reviews
Only logged in customers who have purchased this product may leave a review.
Related products
-
Category Name, Electronics, ELRS Receivers
RadioMaster RP3 2.4GHz ELRS Diversity Receiver v2
The RadioMaster RP series of receivers are designed with size, ease of use, and range in mind. Utilizing ExpressLRS 2.4ghz Open-source firmware the RP series of nano receivers deliver features and range today’s pilots have come to expect.
Developed around the ESP8285 MCU and SX1280IMLTRT RF Chip the RP series offer Lora and FLRC 2.4ghz RF links offering incredible range and low latency. With Wifi built-in, firmware updates can be done on your craft without the need to remove the receiver. Binding can be done using a bind phrase meaning no more bind plugs or fiddly button presses while trying to plug in your battery.
The RP3 receiver features a Skyworks SE2431L providing an LNA for improved receiver performance, a PA providing up to 100mw of telemetry performance, and antenna switching for antenna diversity.
Features:
- Optimized PCB design for better heat dissipation.
- LNA for better receiver range.
- PA for better telemetry range.
- Antenna Diversity for improved signal stability and range.
SKU: RM.RP3.RX.ELRS.V2. -
Category Name, Electronics, ELRS Receivers
Happymodel EP1 2.4GHz RX ELRS Receiver
The PP RX is designed by @Jye Smith from ExpressLRS development team. Its main hardware architecture is STM32L432KBU6 MCU and SX1280 RF chip. On the basis of PP RX, we have developed the Nano 2.4GHz rx of ESP8285 version named EP1 and EP2. The RF module of EP1/EP2 is the same like PP RX and use ESP8285 MCU . So you can upgrade firmware by WIFI , that’s too simple. Due to the low-latency and high-refresh-rate RF module, they are very comfortable for FPV race and Long Range FPV. And very suitable for whoop because of the ultra light and Nano size.
SKU: HM.EP1.RX.ELRS. -
Electronics, Other Electronics
ViFly GPS-mate External GPS Power Module
Tired of draining your battery as you wait for the GPS fix? Wish the GPS was self-powered so that it didn’t have to get a new fix every time you plug up a new pack? Battery ejected during crash and now the GPS is useless? The GPS-mate is what you’re looking for!
Why Vifly designed the GPS-mate?
Most drone pilots have a problem when using the GPS on their drones. GPS modules are slow, and get interference. To get a fix, a pilot must wait many minutes for a GPS fix. To do this, everything must be powered, which drains the battery and causes extra interference. It also has potential risk to cause overheating issues to your quad components. In addition, when you finish a flight cycle and change the quad battery, the GPS needs to get a hot-start fix as the quad battery disconnected. We want to fix the pain, so we design and produce GPS-mate, the external power module just for GPS.What exactly does the GPS-mate do?
VIFLY GPS-mate is an external power module just for GPS, there is a switch to turn on and off the unit. With this device, once the pilot wants to fly, he flips the switch and only the GPS gets powered. When the GPS fix finished, the pilot connects the drone LiPo. The drone LiPo powers the drone, and recharges the GPS battery. The GPS never loses power until the switch is turned off, so the pilot never needs to get another fix for the whole session.We also embed VIFLY Finder 2 function into this device, it can work as a standard buzzer that controlled via your radio when the quad battery is connected, it also can work as a standalone buzzer that help you find the lost drone when the main battery has been ejected.
SKU: VF.GMATE.MODULE.
There are no reviews yet.