Happymodel SuperbeeF4 Lite AIO 1S FC 2.4GHz ELRS
Out of stock
The direct replacement AIO board for the Mobula6 HDZero. The default OSD is set to “MSP” since this is considered spare part for the Mobula6 HDZero.
If using this board with an analog camera you will need to change some settings in BetaFlight. Instructions can be found at SuperbeeF4
* ELRS version
$40.99 $46.99
Out of stock
Features:
- Built-in 5A Blheli_S 4in1 ESC, Dshot600 ready
- Built-in Betaflight OSD (SPI Control)
- Built-in SPI ELRS Receiver
- Built-in 5V/1A BEC
Specifications:
- Superbee F4 lite ELRS FC Firmware target: CrazybeeF4SX1280
- Power supply: 1S LiPo/ Lihv battery input (DC 2.8V-4.35V)
- MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
- OSD: Built-in Betaflight (SPI Control)
- Sensor: MPU-6000or ICM20689 or BMI270Â (SPI connection)
- BEC: Built-in 5V 1A
SPI ELRS V2.0 RECEIVER
- Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
- Compatibility: ExpressLRS V2.0 TX Module
- Antenna: Enameled copper wire antenna
- ExpressLRS Firmware version: V2.0
- Receiver protocol: SPI ExpressLRS
- Telemetry output Power: <12dBm
- RF Frequency: 2.4GHz
ONBOARD 4-IN-1 ESC
- Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (5seconds)
- Factory firmware: S_H_50HEX
- Support BLHeliSuite programmable
- MCU upgraded to EFM8BB21
- Default protocol: DSHOT600
Included:
- 1 x Happymodel SuperbeeF4lite AIO Flight Controller – SPI ELRS
- 2 x Connecting Wire
- 4 x Damping Balls
- 4 x Screws
Based on 0 reviews
Only logged in customers who have purchased this product may leave a review.
Related products
-
Category Name, Electronics, ELRS Receivers
RadioMaster RP2 2.4GHz ELRS Nano Receiver v2
The RadioMaster RP2 ExpressLRS 2.4ghz Nano Receiver w/ Fixed SMT Antenna is an open-source receiver based on ExpressLRS. It features an ESP8285 MCU and an SX1280 RF chip. The RP2 has a built-in ceramic antenna which is super light and small in size and ideal for racing. The RP2 features WIFI built in so you can upgrade firmware by WIFI and configure the Receiver via the built-in WebUI with your PC or mobile phone. Due to the low-latency and high-refresh-rate RF module, the RP2 is ideal for FPV racing or Long Range flights. Suitable for whoops, drones, and fixed-wing models due to the ultra-light and Nano size, these receivers can fit just about anywhere!
Features
- Built-in WIFI so you can upgrade firmware by WIFI and configure the Receiver via the built-in WebUI with your PC or mobile phone
- Upgraded rigid antenna with greater durability and performance
- Improved PCB design is better for heat dissipation
- Solder pads are improved and easier to solder to
- Low-latency and high-refresh-rate RF module
- Open-source receiver based on ExpressLRS
- LED on the top side of PCB
- Built-In ceramic antenna
- SX1280 RF chip
- ESP8285 MCU
SKU: RM.RP2.RX.ELRS.V2. -
Category Name, Electronics, Flight Controllers
Happymodel CrossF4 F411 1-2S 5A AIO Whoop Flight Controller with UART ELRS v3.0 receiver – ELRS 2.4gHz
Category Name, Electronics, Flight ControllersHappymodel CrossF4 F411 1-2S 5A AIO Whoop Flight Controller with UART ELRS v3.0 receiver – ELRS 2.4gHz
HappyModel keeps them coming! Now with yet another fantastic whoop AIO. The HappyModel CrossF4 1-2S AIO Whoop Flight Controller (F4 FC / 5A 4in1 ESC) – Featuring F411 Flight Controller, with a built in serial UART ELRS for V3.0.
NOTE:Â Onboard blackbox enable method:
-Type the following command to CLI:
-set blackbox_device = SPIFLASH
-set flash_spi_bus = 2
-resource FLASH_CS 1 a14Pay attention: Bind procedure is the same like Happymodel EP1/EP2 receiver, as you need to upgrade your ExpressLRS TX module to V3.X version first.
Alternative-Binding-Method-for-UART-Based-ELRS-RX
Onboard blackbox enable method:
Type the following command to CLI:
set blackbox_device = SPIFLASH
set flash_spi_bus = 2
resource FLASH_CS 1 a14
saveSKU: HM.CROSSF.FC.ELRS -
Category Name, Electronics, ELRS Receivers
RadioMaster RP3 2.4GHz ELRS Diversity Receiver v2
The RadioMaster RP series of receivers are designed with size, ease of use, and range in mind. Utilizing ExpressLRS 2.4ghz Open-source firmware the RP series of nano receivers deliver features and range today’s pilots have come to expect.
Developed around the ESP8285 MCU and SX1280IMLTRT RF Chip the RP series offer Lora and FLRC 2.4ghz RF links offering incredible range and low latency. With Wifi built-in, firmware updates can be done on your craft without the need to remove the receiver. Binding can be done using a bind phrase meaning no more bind plugs or fiddly button presses while trying to plug in your battery.
The RP3 receiver features a Skyworks SE2431L providing an LNA for improved receiver performance, a PA providing up to 100mw of telemetry performance, and antenna switching for antenna diversity.
Features:
- Optimized PCB design for better heat dissipation.
- LNA for better receiver range.
- PA for better telemetry range.
- Antenna Diversity for improved signal stability and range.
SKU: RM.RP3.RX.ELRS.V2. -
Electronics, Flight Controllers
Happymodel X2 AIO F4 Flight Controller SPI ELRS RX 2-4S 12A ESC
The Happymodel ELRS X2 AIO Flight Controller is the direct replacement for the Mobula7 HDZero.
It comes with an integrated SPI 2.4GHz ELRS receiver and 12A Blheli_S ESC which supports 2-4S batteries. Bigger mosfet supports high to 12A currents and would be better for a 2-4S toothpick drone or long-range FPV drone. The 2.4GHz ExpressLRS receiver is equipped with the SX1280 radio frequency chip with high sensitivity, high packet rate, and low latency. Featuring an MPU 6000 SPI sensor and OSD, this board is the perfect addition to your FPV build.
SKU: HM.X2F4.FC.ELRS.
There are no reviews yet.