ViFly GPS-mate External GPS Power Module
Tired of draining your battery as you wait for the GPS fix? Wish the GPS was self-powered so that it didn’t have to get a new fix every time you plug up a new pack? Battery ejected during crash and now the GPS is useless? The GPS-mate is what you’re looking for!
Why Vifly designed the GPS-mate?
Most drone pilots have a problem when using the GPS on their drones. GPS modules are slow, and get interference. To get a fix, a pilot must wait many minutes for a GPS fix. To do this, everything must be powered, which drains the battery and causes extra interference. It also has potential risk to cause overheating issues to your quad components. In addition, when you finish a flight cycle and change the quad battery, the GPS needs to get a hot-start fix as the quad battery disconnected. We want to fix the pain, so we design and produce GPS-mate, the external power module just for GPS.
What exactly does the GPS-mate do?
VIFLY GPS-mate is an external power module just for GPS, there is a switch to turn on and off the unit. With this device, once the pilot wants to fly, he flips the switch and only the GPS gets powered. When the GPS fix finished, the pilot connects the drone LiPo. The drone LiPo powers the drone, and recharges the GPS battery. The GPS never loses power until the switch is turned off, so the pilot never needs to get another fix for the whole session.
We also embed VIFLY Finder 2 function into this device, it can work as a standard buzzer that controlled via your radio when the quad battery is connected, it also can work as a standalone buzzer that help you find the lost drone when the main battery has been ejected.
$13.99
Specifications:
- Weight 3.5g
- Size 26 X 20 X 8 mm
- LiPo Voltage 3.7V
- LiPo Size 50mAh
- Buzzer Working Time Up to 4 hours
- Input Voltage 4.5-5.5V
- Charging Time 1.5 Hours
- Output Current Up to 80mA
- Buzzer Volume Up to 90dB
Included:
- 1 x GPS-mate, 4pin Cable, 5pin Cable, Cable Tie, Manual
Based on 0 reviews
Only logged in customers who have purchased this product may leave a review.
Related products
-
Electronics, Flight Controllers
Happymodel X2 AIO F4 Flight Controller SPI ELRS RX 2-4S 12A ESC
The Happymodel ELRS X2 AIO Flight Controller is the direct replacement for the Mobula7 HDZero.
It comes with an integrated SPI 2.4GHz ELRS receiver and 12A Blheli_S ESC which supports 2-4S batteries. Bigger mosfet supports high to 12A currents and would be better for a 2-4S toothpick drone or long-range FPV drone. The 2.4GHz ExpressLRS receiver is equipped with the SX1280 radio frequency chip with high sensitivity, high packet rate, and low latency. Featuring an MPU 6000 SPI sensor and OSD, this board is the perfect addition to your FPV build.
SKU: HM.X2F4.FC.ELRS. -
-
Electronics, Flight Controllers
Happymodel ELRS 2G4 Whoop Flight Controller
The world’s first AIO 5in1 F4 flight controller with integrated SPI 2.4GHz ExpressLRS receiver has been launched. The flight controller integrates SPI controlled 2.4GHz ExpressLRS receiver, Dshot protocol 4-in-1 ESC, 5.8GHz 40ch video transmitter and Betaflight OSD. Ultra-small size and ultra-stable remote control range can improve the range of the original SPI receiver. And because the 2.4GHz ExpressLRS receiver is equipped with the SX1280 radio frequency chip with high sensitivity, high packet rate and low latency, this flight controller is the one that all Race/Freestyle pilots needed. It is suitable for use in Tiny whoop Race or Toothpick Freestyle, and can also be used in 1S ultra-lightweight Nano Long Range platform.
SKU: HM.2G4.FC.ELRS. -
Electronics, ELRS Receivers
HappyModel EP2 2.4GHz RX ELRS Receiver
Happymodel’s 2.4GHz ELRS nano series receiver with tiny ceramic antenna.
The PP RX was designed by @Jye Smith from the ExpressLRS development team. Its main hardware architecture is STM32L432KBU6 MCU and SX1280 RF chip. It has a built-in ceramic antenna, which is super light and small in size.
On the basis of that PP RX, Happymodel has developed the Nano 2.4GHz RX of ESP8285 version named EP1 and EP2. The RF module of EP1/EP2 is the same as PP RX and uses ESP8285 MCU. You can upgrade firmware via WiFi!
Due to the low-latency and high-refresh-rate RF module, they are very comfortable for FPV race and Long Range FPV. These are very suitable for Tiny Whoops because of the ultra-light and Nano size!Note: This is the EP2 RX Version
SKU: HM.EP2.RX.ELRS.
There are no reviews yet.