Happymodel DiamondF4 ELRS 5-in-1 AIO FC 2.4GHz
Happymodel’s AIO triangle-shaped whoop board! The Diamond F4 5-in-1 AIO board makes building whoops easy as picking your camera, motors, and frame.
*Direct replacement AIO for the Moblite6/Moblite 7 whoops
*ELRS Version
$60.99
Features:
- Diamond Mounting Pattern – 22.2 x 22.2 x 32.7mm
- Built-in 5A Blheli_S 4in1 ESC, Dshot600 ready
- Built-in Betaflight OSD (SPI Control)
- Built-in 25-200mW 5.8GHz VTX
- Built-in SPI ELRS Receiver
- Built-in 5V/1A BEC
Specifications:
- DiamondF4 ELRS FC Firmware target: CrazybeeF4SX1280
- Power supply: 1S battery input (DC 2.9V-4.35V)
- MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
- OSD: Built-in Betaflight (SPI Control)
- Sensor: MPU-6000 (SPI connection)
- BEC: Built-in 5V 1A
SPI ELRS V2.0 RECEIVER
- Packet Rate option: 50Hz/150Hz/250Hz/500Hz
- Compatibility: ExpressLRS V2.0 TX Module
- Antenna: Enameled copper wire antenna
- ExpressLRS Firmware version: V2.0
- Receiver protocol: SPI ExpressLRS
- Telemetry output Power: <12dBm
- RF Frequency: 2.4GHz
ONBOARD 4-IN-1 ESC
- Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds)
- Factory firmware: O_H_5_REV16_8.HEX
- Support BLHeliSuite programmable
- MCU upgraded to EFM8BB21
- Default protocol: DSHOT600
ONBOARD 5.8 GHZ VTX
- Transmitting Power: 0/RCE/25mw/100mw/400mw
- Current (5v): <650ma (400mw)
- Firmware version: OPENVTX
- Power supply:Â DC 5V
- RCE Mode support
- PIT Mode support
- Smart audio v2.1
- Channels:48ch
Included:
- 1 x Happymodel Diamond F4 FR AIO 5-in-1 Flight Controller – SPI ELRS
- 2 x Connecting Wire
- 4 x Damping Balls
- 4 x Screws
Based on 0 reviews
Only logged in customers who have purchased this product may leave a review.
Related products
-
Category Name, Electronics, Flight Controllers
Happymodel CrossF4 F411 1-2S 5A AIO Whoop Flight Controller with UART ELRS v3.0 receiver – ELRS 2.4gHz
Category Name, Electronics, Flight ControllersHappymodel CrossF4 F411 1-2S 5A AIO Whoop Flight Controller with UART ELRS v3.0 receiver – ELRS 2.4gHz
HappyModel keeps them coming! Now with yet another fantastic whoop AIO. The HappyModel CrossF4 1-2S AIO Whoop Flight Controller (F4 FC / 5A 4in1 ESC) – Featuring F411 Flight Controller, with a built in serial UART ELRS for V3.0.
NOTE:Â Onboard blackbox enable method:
-Type the following command to CLI:
-set blackbox_device = SPIFLASH
-set flash_spi_bus = 2
-resource FLASH_CS 1 a14Pay attention: Bind procedure is the same like Happymodel EP1/EP2 receiver, as you need to upgrade your ExpressLRS TX module to V3.X version first.
Alternative-Binding-Method-for-UART-Based-ELRS-RX
Onboard blackbox enable method:
Type the following command to CLI:
set blackbox_device = SPIFLASH
set flash_spi_bus = 2
resource FLASH_CS 1 a14
saveSKU: HM.CROSSF.FC.ELRS -
Electronics, Flight Controllers
Happymodel Pancake 2-6S F4 AIO Flight Controller SPI ELRS RX + 5.8GHz OpenVTX
Electronics, Flight ControllersHappymodel Pancake 2-6S F4 AIO Flight Controller SPI ELRS RX + 5.8GHz OpenVTX
The Pancake AIO was designed with the help of the ExpressLRS team. It features an onboard 2.4GHz ELRS SPI receiver as well as a 5.8 GHz OpenVTX with up to 400mw of power. It can be mounted using the 30.5mm or 20mm spaced holes.
SKU: HM.PANCAK.FC.ELRS. -
-
Electronics, Flight Controllers
Happymodel X2 AIO F4 Flight Controller SPI ELRS RX 2-4S 12A ESC
The Happymodel ELRS X2 AIO Flight Controller is the direct replacement for the Mobula7 HDZero.
It comes with an integrated SPI 2.4GHz ELRS receiver and 12A Blheli_S ESC which supports 2-4S batteries. Bigger mosfet supports high to 12A currents and would be better for a 2-4S toothpick drone or long-range FPV drone. The 2.4GHz ExpressLRS receiver is equipped with the SX1280 radio frequency chip with high sensitivity, high packet rate, and low latency. Featuring an MPU 6000 SPI sensor and OSD, this board is the perfect addition to your FPV build.
SKU: HM.X2F4.FC.ELRS.
There are no reviews yet.