Flywoo Firefly DC16 Nano Baby Walksnail V2.0 1S Deadcat Micro 1.6″ – ELRS 2.4 GHz

Features

• Redesigned canopy with enhanced aesthetics and reinforced camera protection.
• The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter.
• Equipped with ROBO 1002 19800KV motor and 1608 3-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability.
• The GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance.
• A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector.
• New battery compartment design allows for easy replacement of batteries of different models.

Dead Cat Style

New Design

Redesigned canopy with enhanced aesthetics and reinforced camera protection.
Bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter.

Efficient Power Combo

Equipped with ROBO 1002 19800KV motor and 1608 3-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability.

Ultra-light AIO with ELRS 2.4G RX

The drone’s GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance. This allows for the ultimate lightweight design without sacrificing functionality.

HD Digital VTX System

The Walksnail Avatar HD Mini 1S Lite is a lightweight VTX designed for 1S whoop drones, featuring H.265 high-efficiency video coding technology, 1080P/60FPS image recording with 22ms ultra-low latency, and built-in 8 GB storage for interference-free HD video recording and USB exporting. 

More Power, More Flight Time

The A30 plug can sustain a continuous current of 15A, whereas the PH2.0 connector can only support 4.5A. Given the same capacity, the A30 plug can release more current, providing greater power and, as a result, longer flight times even when flying at full speed. 

Specifications:

• Frame Kit: Firefly 1S DC16 Nano baby quad Frame kit
• Motor: ROBO 1002 19800KV
• Electronic: GOKU Versatile F411 ELRS 1S 5A AIO V2.0
• Propeller: 1608-3 Blade 40mm 1.5mm Shaft
• Camera: Avatar Lite Cam
• Weight: 33g

GOKU Versatile F411 ELRS 1S 5A AIO V2.0
Flight Controller

• MCU: STM32F411CEU6
• GYRO: ICM42688
• UARTS: 1/2
• Soft serial port: 1
• I2C: SCL/SDA
• BEC: 5V
• Input Voltage: 1S (<4.35v)
• Firmware: FLYWOOF411_5IN1_AIO 
• Mounting:  25x25mm, M2

Onboard 4in1 ESC

• MCU: EFM8BB21
• Power supply: 1S LiPo/LiPo HVCurrent: 5A
• Firmware: BLHeli_S
• Factory firmware: O_H_5_REV16_8.HEX
• Default protocol: DSHOT 150/300/600
• ELRS 2.4G RX (UART2)

ROBO 1002 19800KV

• Configuration: 9N12P
• Stator Diamter: 10mm
• Stator Length: 2mm
• Shaft Diameter: 1.5mm
• Motor Dimension(Dia.xLen): Φ13.5×7.75mm
• Weight(g): 2.5(5cm wire)
• Idle current(5)@5V(A): 1.3
• No.of Cells(Lipo): 1S
• Max Continuous Power(W)3S: 44
• Internal Resistance: 89mΩ
• Max Current(3S): 11.8A
• Max Efficiency Current: (2-4A)>84%

Walksnail Avatar HD Mini 1S Lite

• Model: Avatar mini 1s module
• Communication Frequency: 5.725-5.850GHz
• Transmitter Power (EIRP): FCC:<25.5dBm;CE:<14dBm;SRRC:<20dBm;
• MIC:<25dBm
• I/O Interface: JST1.0x6(Power in)JST1.0x4(USB)
• Mounting Holes: 25.5×25.5mm
• Dimensions: 30x30x6.5mm
• Storage: 8G
• Recording: 1080p/720p
• Weight: 5.1g
• Operating Temperature: -20-40℃
• Channels: 8
• Wide Power Input: 3.1V-5V
• Supported FC System: Betaflight
• OSD: Canvas mode
• Bitrate: 25mbps, 50mbps
• Latency Average delay: 22ms
• Antenna: IPEX

Avatar lite camera

• Model: Avatar lite camera
• Image Sensor: 1/2.7”1nch
• Resolution: 1080P/60fps,720P/120fps,720P/60fps
• Ratio: 16/9 4/3
• Lens:2.1mm
• FOV:170°
• Aperture:F2.0
• Shutter Rolling: Rolling shutter
• Min.Illumination: 0.001Lux
• Weight: 1.8g
• Dimensions: 14x14x16mm

Included:

• Flywoo BNF Firefly DC16 Nano Baby V2.0 HD 1S 1.6″ Deadcat Micro Quad w/ Walksnail Avatar Mini 1S Lite & Avatar Lite Cam – ELRS 2.4 GHz x 1
• 1608 -3 40mm 1.5mm shaft x 4
• TPU battery mount x 2
• Hardware screws set x 1
• Prop guards x 4