, ,

Happymodel Mobula7 DJI O4 2S 80mm Whoop Drone – ELRS 2.4GHz

The Happymodel Mobula7 O4 micro FPV whoop is out now!  It comes with the new DJI O4 air unit which would provide excellent and unbelievable FPV footage.  It features the new Happymodel RS1102 KV10000 motors with HQPROP 45mm propellers, which bring a powerful and smooth flying experience.  This would be a good option for indoor and backyard FPV flying.

*NOTICE before purchasing: According to DJI’s warranty policy, if there is a problem with the DJI O4 Air unit installed on the BNF Drone, it needs to be sent back to China mainland for warranty.

 

 

$272.99

***If you want to use DJI FPV Remote controller, Please first reflash betaflight firmware add add “SBUS” protocol support when load firmware online. And then please import defaulct factor dump file to CLI command , then change betaflight settings like following picture,no need do any hardware modification to the flight controller:

Features:

  • Equipment with New DJI O4 air unit
  • 2S battery support Powerful and Smooth freestyle flying
  • UART ExpressLRS receiver support stable control link
  • Lighter and small for indoor FPV

Specifications:

Motor

  • Mode: RS1102 KV10000
  • Configu-ration:9N12P
  • Stator Diamter:11mm
  • Stator Length:2mm
  • Shaft Diameter:Φ1.5mm
  • Motor Dimension(Dia.*Len):Φ13.5mm*14mm
  • Weight(g):2.8g
  • No.of Cells(Lipo):1-2S

Propellers:

  • Weight:0.33g
  • Material: Poly Carbonate
  • Pitch:0.9
  • Props Dia:45mm
  • Hub Thickness:5mm
  • Shaft:1.5mm

Flight controller:

  • MCU: STM32F405RGT6 (168MHZ, 1Mbyte FLASH)
  • GYRO Sensor: BMI270  (SPI connection)
  • Mount hole size: 25.5mm*25.5mm
  • Power supply: 1-2S battery input (DC 2.9V-8.7V)
  • Built-in 12A(each) Blheli_S 4in1 ESC
  • Built-in Serial ExpressLRS 2.4G
  • Built-in BMP280 Barometer
  • Built-in 8MBp blackbox
  • Built-in voltage meter sensor , voltage meter scale 110
  • Built-in current meter sensor , current meter scale 470

Onboard 4in1 ESC:

  • Power supply: 1-2S LiPo/LiPo HV
  • Current: 12A continuous peak 15A (3 seconds)
  • Support BLHeli_S Bluejay firmware
  • Factory firmware: Bluejay ESC V0.19
  • Firmware target: Z-H-30
  • Default protocol: DSHOT300
  • When use 1s battery and high KV 0702/0802 motors, should set startup power to 1100/1200

Onboard UART ExpressLRS 2.4GHz Receiver:

  • Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
  • RF Frequency: 2.4GHz
  • Antenna: enameled copper wire 31mm length
  • Telemetry output Power: <12dBm
  • Default firmware version: ExpressLRS V3.0.1
  • Firmware target: HappyModel EP 2400 RX
  • Could update firmware via ExpressLRS configurator

DJI O4 Air Unit:

  • Weight:
    Air Unit (camera module included): Approx. 8.2 g
  • Transmission Module: 30×30×6 mm (L×W×H)
  • Camera Module: 13.44×12.36×16.50 mm (L×W×H)
  • Camera Cable Length: 50mm
  • Coaxial Cable: 50 mm
  • 3-in-1 Cable: 50 mm
  • Operating Frequency:
    5.170-5.250 GHz
    5.725-5.850 GHz
  • Operating frequency varies by region. Refer to local regulations.
    Transmitter Power (EIRP):
    5.1 GHz: <23 dBm (CE)
    5.8 GHz:
    <30 dBm (FCC)
    <14 dBm (CE)
    <30 dBm (SRRC)
  • Live View Quality: 1080p at 30/50/60/100fps

Included:

  • Happymodel M80 Frame x1
  • CrazyF405HD ELRS flight controller firmware target:BETAFLIGHTF4 x1
  • RS1102 KV10000 brushless motor x4
  • HQPROP 45MMX3 tri-blade propellers(4cw+4ccw) x1
  • DJI O4 Air unit x1
  • Canopy x1
  • Screw driver x1
SKU: HM.MOBUL7.04.ELRS. Categories: , ,

Based on 0 reviews

0.0 overall
0
0
0
0
0

Only logged in customers who have purchased this product may leave a review.

There are no reviews yet.

Related products

Join Waitlist We will inform you when the product arrives in stock. Please leave your valid email address below.

No fields found, please go to settings & save/reset fields